Product Description And Applications - Nice F210S Instructions Et Avertissements Pour L'installation Et L'utilisation

1) Warnings
This manual contains important information regarding safety
during installation, therefore before starting installation, it is
important that you read all the information contained herein.
Store this manual in a safe place for future use.
Due to the dangers which may arise during both the installa-
tion and use of the F210, installation must be carried out in full
respect of the laws, provisions and rules currently in force in
order to ensure maximum safety.
According to the most recent European legislation, the
automation of a door or gate is governed by the provi-
sions listed in Directive 98/37/CE (Machine Directive)
and, more specifically, by provisions: EN 13241-1 (har-
monized standard); EN 12445; EN 12453 and EN 12635,
which enable to declare the conformity of the product
to the machine directive.
Further information, risk analysis guidelines and how to draw
up the Technical Documentation are available at: www.nice-
foryou.com". This manual has been especially written for use
by qualified fitters, none of the information provided in this
manual can be considered as being of interest to end users!
• The use of F210S which is not explicitly provided for in
these instructions is not permitted. Improper use may
cause damage and personal injury.
• Do not modify any components unless such action is
specified in these instructions. Operations of this kind are
likely to lead to malfunctions. NICE S.p.a. disclaims any lia-
bility for damage resulting from modified products.
• F210S must only function through TX-RX direct interpola-
tion. Use through reflection is prohibited.
• F210S has to be permanently fixed to a firm and vibration-
free surface.

2) Product description and applications

The F210S directional photocells are presence detectors
(type D in compliance with the EN12453 standard) that can
be used for the automation of vertically rolling shutters, doors
and the like. They are able to detect obstacles on the optical
axis between the (TX) transmitter and the (RX) receiver.
The F210S photocells can only be used with tubular motors
and preset control units; they are powered and communicate
with the control unit by means of a two-wire TTBUS connec-
tion. Refer to the product manual to check if the F210S can
be used.
The RX receiver foresees the possibility of connecting "open-
ing" and "closing" (or "Step by Step") and "stop" control but-
tons. An input for sensitive edges is also available with an
8.2KΩ constant resistance output through which C type
safety devices can be produced in accordance with the EN
12453 standard.
!
The F210S does not comprise a complete safety
device but is only part of it.
• Use suitable conductors for the electrical connections as
specified in the "installation" chapter.
• Make sure that the electrical power supply and the other
use parameters correspond to the values indicated in
"technical characteristics" table.
• The manufacture of safety devices for automatic doors and
gates is subjected to the following standards:
• EN 12453 Industrial, commercial and garage doors and
gates. Safety in use of power operated doors - Require-
ments
• EN 12978 Industrial, commercial and garage doors and
gates. Safety devices for power operated doors and
gates - Requirements and test methods
The installation and connection of the F210S as a safety
device must be performed in compliance to the said stan-
dards, if the necessary provisions are not taken, this will be
automatically considered as negligence and deliberate
abuse.
Particular warnings concerning the suitable use of this product
in relation to the 89/336/EEC "Electromagnetic Compatibility"
Directive and subsequent modifications 92/31/EEC and
93/68/EEC: This product has been subjected to tests regard-
ing the electromagnetic compatibility in the most critical of use
conditions, in the configurations foreseen in this instructions
manual and in combination with articles present in the Nice
S.p.a. product catalogue The electromagnetic compatibility
may not be guaranteed if used in different configurations or
with other products that have not been foreseen; the use of the
product is prohibited in these situations until the correspon-
dence to the requirements foreseen by the directive has been
verified by those performing the installation.
Typical use
1
2