Description And Operation; Safety; Typical Applications; Installation - Vortice CA ES Série Notice D'emploi Et D'entretien

ENGLISH

Description and operation

The appliance you have purchased is a metal
construction, centrifugal in-line extractor fan,
designed to expel air through a ventilation duct.
The appliance has an electronically controlled two-
speed brushless motor with maximum and minimum
speed settings.

Safety

Warning:
!
this symbol indicates that care must
be taken to avoid injury to the user
• Do not use this appliance for functions other than
those described in this booklet
• After removing the appliance from its packaging,
ensure that it is complete and undamaged. If in
doubt contact a professionally qualified electrician
or Vortice. Do not leave packaging within the reach
of children or infirm persons
• Certain fundamental rules must be observed when
using any electrical appliance, including:
- never touch electrical appliances with wet or
damp hands;
- never touch appliances while barefoot;
- never allow children or infirm persons to operate
appliances unattended.
• Store the appliance out of the reach of children and
differently able persons after deciding to disconnect
it from the power supply and use it no more.
• Do not us the appliance where flammable vapours
are present (spirit, insecticides, petrol, etc.).
Caution:
!
this symbol indicates that care must
be taken to avoid damaging the appliance
• Do not make modifications of any kind to this
appliance.
• Do not expose this appliance to the weather (rain,
sun, etc.).
• Do not place objects on top of the appliance.
• Regularly inspect the appliance for visible defects. If
the appliance does not function correctly, do not
use it and contact Vortice immediately.
• If the appliance does not function correctly or
develops a fault, contact Vortice immediately and
ensure that only genuine original Vortice spares are
used for any repairs.
• Should the appliance be dropped or suffer a heavy
blow, have it checked immediately by Vortice
• The appliance must be installed by a professionally
qualified electrician
• The mains power supply to which the units are
connected must comply with current laws.
• The electrical power supply/socket to which the
appliance is to be connected must be able to
provide the maximum electrical power required by
the appliance
• Use a suitably sized multi-polar switch with
minimum contact gaps of 3 mm to install the
appliance.
• Switch off the appliance at the installation's main
switch: a) if the appliance does not function
correctly; b) before cleaning the outside of the
appliance, c) if the appliance is not to be used for
any length of time.
• Ensure that the room has an adequate source of
fresh air to ensure correct appliance operation. In
the event that other non-sealed combustion-based
appliances (such as water heater or gas stove) are
installed in the same room, check that air
replacement is sufficient for all appliances to work
effectively together.
• The appliance cannot be used to control activation
of water heaters, room heaters, etc. and it must not
exhaust into the hot air flues.
• Ensure that the appliance discharges into a single
duct (dedicated to this product) or directly to the
outside.
• The appliance's inlet and outlet ports must always
be connected to a suitable duct.
• The maximum ambient temperature for the proper
functioning of the appliance is 50° C.
• The overtemperature and overload protection is
assured by the fuse and the control electronics.
• Specifications for
correspond to the electrical data on data plate A
(Fig.1)
Typical application
Fig. 2 ÷ 5;
Fig. 5: A= inlet; B= outlet
NOTE
The appliance's inlet and outlet ports must always be
connected to a suitable duct.

Installation

Fig. 6 ÷12.
NOTE
Use of the supplied brackets is optional.

Initial Configuration

The installer must configure appliance operation by
following the steps described later on.
selecting the product model: see below. This step is
carried out in the factory; the instructions provided in
this booklet may only be of use if it becomes
necessary to reset the status following accidental
tampering with the dip-switch.
selecting the operating mode: see below. There are
two modes: with two speeds V1 and V2, which can be
selected via an external switch, or with speed that can
be adjusted via an external potentiometer.
setting the V1 and V2 values (for two-speed operating
mode)
the power supply must