Functional Description - Hitachi CH 36DL Mode D'emploi

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 24
English
(2) Regarding the temperature of the rechargeable
battery.
The temperatures for rechargeable batteries are as
shown in Table 2, and batteries that have become hot
should be cooled for a while before being recharged.
Table 2 Recharging ranges of batteries
Rechargeable batteries
BSL3620
(3) Regarding recharging time
Depending on the combination of the charger and
batteries, the charging time will become as shown in
Table 3.
Table 3 Charging time (At 20°C)
Charger
Battery
BSL3620
NOTE
The charging time may vary according to temperature
and power source voltage.
4. Disconnect the charger's power cord from the
receptacle
5. Hold the charger firmly and pull out the battery
NOTE
After charging, pull out batteries from the charger
first, and then keep the batteries properly.
How to make the batteries perform longer.
(1) Recharge the batteries before they become completely
exhausted.
When you feel that the power of the tool becomes
weaker, stop using the tool and recharge its battery. If
you continue to use the tool and exhaust the electric
current, the battery may be damaged and its life will
become shorter.
(2) Avoid recharging at high temperatures.
A rechargeable battery will be hot immediately after
use. If such a battery is recharged immediately after
use, its internal chemical substance will deteriorate,
and the battery life will be shortened. Leave the battery
and recharge it after it has cooled for a while.
CAUTION
If the battery is charged while it is heated because it
has been left for a long time in a location subject to
direct sunlight or because the battery has just been
used, the pilot lamp of the charger lights up green. In
such a case, first let the battery cool, then start
charging.
When the pilot lamp flickers in red (at 0.2-seconds
intervals), check for and take out any foreign objects
in the charger's battery connector. If there are no
foreign objects, it is probable that the battery or
charger is malfunctioning. Take it to your authorized
Service Center.
Since the built-in micro computer takes about 3
seconds to confirm that the battery being charged
with UC36YRSL is taken out, wait for a minimum of 3
seconds before reinserting it to continue charging. If
the battery is reinserted within 3 seconds, the battery
may not be properly charged.
9
Temperatures at which the
battery can be recharged
0°C – 50°C
UC36YRSL
Approx. 60 min.

FUNCTIONAL DESCRIPTION

1. Switch ON (Fig. 5)
The blade starts moving by pulling the trigger of the
main handle while holding the sub handle.
2. Switch OFF (Fig. 5)
The blade stops moving by releasing the trigger of
the main handle or the sub handle.
3. Blade case (Fig. 6)
When the hedge trimmer blade is to be attached to or
removed from the tool, or when the shear is not used,
place the blade in the blade case to prevent injury.
WARNING
Be sure to turn the tool off and remove the battery
from the tool before attaching and removing the
blade case.
CAUTION
To prevent injury, take care when placing the blade
in the blade case.
4. Speed adjustment (Fig. 7)
According to the work contents and branches to trim,
the blade speed has 4 adjustable settings.
The speed increases when the selector button is
pressed, and the number of illuminated LEDs (green)
increases.
4 LEDs illuminated: 1500 min
3 LEDs illuminated: 1330 min
2 LEDs illuminated: 1170 min
1 LED illuminated: 1000 min
NOTE
The battery must be mounted to the main body and
the trigger of the main handle must be pulled
otherwise the LED will not light up, even though the
selector button is pressed.
5. Battery level (Fig. 7)
By pressing and holding the selector button (for at
least 2 seconds), the LED (red) will light up and you
can check the battery level.
The light status of the LED and battery level are as
follows:
2 LEDs illuminated
1 LED illuminated
No LED illuminated
NOTE
The battery must be mounted to the main body and
the trigger of the main handle must be pulled,
otherwise the LED will not light up, even though the
selector button is pressed.
-1
-1
-1
-1
Sufficient battery
:
remains.
:
Battery half-empty
:
Battery very low.
Please recharge as
soon as possible.

Publicité

Table des Matières
loading

Table des Matières