Setting Other Data On Your Controller; Set Clock - CASTLE Serenity Instructions D'utilisation

2. In the "WEEKLY SCHEDULE" screen, you can begin with
setting the operation times for Sunday. Press ENTER to
highlight the hour and use the SCROLL UP and SCROLL
DOWN buttons until you reach your desired hour of
start time. Press ENTER again to highlight the minutes
and use SCROLL UP and SCROLL DOWN until you've
reached your desired minute of start. SEE FIGURE 23.
NOTE: Your Serenity controller uses military time to set
your weekly schedule.
3. Pressing ENTER again will allow you to set the stop time
of your stove. Use the same procedure for setting your
stove's start time for selecting when you would like the
stove to stop. Once you've selected the stop time, press
ENTER.
4. Next you will have the opportunity to set the desired
temperature. Use the SCROLL UP or SCROLL DOWN
keys until you've reached the appropriate temperature
for the times you have selected. Press ENTER.
5. "Yes" will now be highlighted. If you have set this
particular time correctly, press ENTER. This will take you
out of your first set time.
If you wish to erase a scheduled time, use your ENTER
key to highlight "YES" on the screen for that scheduled
time. Select "No" using your SCROLL UP or SCROLL
DOWN key. With "No" highlighted, press ENTER to erase
the data.
6. To set another time for that particular day, press
SCROLL DOWN and continue by repeating steps 2-5 as
appropriate.
NOTE: You must set your times in chronological order.
The first schedule slot of one day MUST be earlier
in the day than the second schedule slot on your
weekly schedule list, etc.
7. Once you have set all times for Sunday, SCROLL DOWN
to "NEXT". Pressing ENTER once will highlight "NEXT".
Pressing ENTER again will take you to the following day.
Proceed with setting a schedule for the rest of the week
using the preceding instructions.
SET WEEKLY
Sun. Weekly Set
1: 1:15~ 7:00
2: 17:00~23:45
3: --:--~--:--
4: --:--~--:--
5: --:--~--:--
Next
Figure 23
26
67°F Yes
72°F Yes
--°F No
--°F No
--°F No
All
Check for parts online at www.castlestoves.com or call 800-450-EDGE (3343) M-F 8-5
Operator's Manual
Serenity Pellet Stove
NOTE: Along with the "Next" option on the screen,
there is also an "All "Option. After you have set
a particular time for a day, if you wish to set that
time for every day of the week, scroll down to
"Next" and press ENTER. Press the SCROLL DOWN
key to select and highlight "All." Pressing ENTER
will then select that scheduled time and apply it to
each day of the week.
TIP: If at any point you need to leave the weekly
schedule screen or once you have finished with
setting all of your times, select the EXIT button
to return to the previous menu.
8. Once you've finished setting your schedule, without any
of the options highlighted, press the EXIT button. This
will save your schedule.
9. With a schedule set, make sure that the main display
screen on the controller reads 'WEEKLY" (for operating
in the Weekly Mode) and that the unit is turned on. The
schedule will not take effect unless the unit is turned on
in the Weekly Mode. (See button 13 on Figure 19.)

Setting Other Data On Your Controller

Setting The Time And Date
ENTER button. This will take you to the
1. Press and hold the
"SET DATA" screen.
ENTER again to enter the "SET CLOCK" screen. SEE
2. Press
FIGURE 24.
3. To change the hour, press
SCROLL UP and SCROLL DOWN buttons
hour. Use your
to choose the appropriate time. Press
correct hour, and then press
setting the minutes.
4. Continue this process for selecting and setting the day, month,
date and year.
5. When finished, and with nothing highlighted on the screen,
EXIT button.
press the

SET CLOCK

10:45 Fri. May 20, 2011
Figure 24
ENTER . This will highlight the
ENTER to select the
ENTER a second time to begin