Bosch GTM 12 JL Professional Notice Originale page 47

OBJ_BUCH-1688-007.book Page 47 Friday, February 24, 2017 12:15 PM
Aligning the Fine Scale (see figure
– Bring the power tool into the chop and mitre saw working
position. (see "Working Position", page 43)
– Turn the saw table 22 to the 0° detent 27. The lever 26
must be felt to engage in the detent.
Checking:
The 0° mark of the fine scale 46 must be in alignment with the
0° mark of the scale 23.
Adjusting:
– Remove the insert plate 24.
– Loosen the screw 55 with the slotted screwdriver provid-
ed and align the fine scale alongside the 0° marks.
– Retighten the screw again.
Aligning the Angle Indicator (Vertically)
(see figure O)
– Bring the power tool into the chop and mitre saw working
position. (see "Working Position", page 43)
– Turn the saw table 22 to the 0° detent 27. The lever 26
must be felt to engage in the detent.
Checking:
The angle indicator 47 must be in alignment with the 0° mark
of the scale 48.
Adjusting:
– Loosen the screw 56 with the slotted screwdriver provid-
ed and align the angle indicator alongside the 0° mark.
– Afterwards, check to ensure that the adjustment made is
correct for the 45° mark.
– Retighten the screw again.
Aligning the Fence
– Bring the power tool into the table saw working position.
(see "Working Position", page 48)
– Turn the saw table 22 to the 0° detent 27. The lever 26
must be felt to engage in the detent.
Checking: (see figure P1)
– Adjust an angle gauge to 90° and position it between the
fence 30 and the saw blade 7 on the saw table 22.
The leg of the angle gauge must be flush with the fence over
the complete length.
Adjusting: (see figure P2)
– Loosen all hex socket screws 39 with the hex key 5 provid-
ed.
– Turn the fence 30 until the angle gauge is flush over the
complete length.
– Retighten the screws again.
Setting the Standard Bevel Angle 0° (Vertical)
– Bring the power tool into the table saw working position.
(see "Working Position", page 48)
– Turn the saw table 22 to the 0° detent 27. The lever 26
must be felt to engage in the detent.
Checking: (see figure Q1)
– Adjust an angle gauge to 90° and position it on the saw ta-
ble 22.
The leg of the angle gauge must be flush with the saw blade 7
over the complete length.
Bosch Power Tools
N) Adjusting: (see figure
– Loosen the nut (size 10 mm) of the Allen screw 57.
– Screw the Allen screw 57 with a suitable Allen wrench (size
3 mm) in or out until the leg of the angle gauge is flush with
the saw blade over the complete length.
– Retighten the nut again.
In case the angle indicator 47 is not in a line with the 0° mark
of the scale 48 after the adjustment, the angle indicator must
be aligned accordingly (see "Aligning the Angle Indicator (Ver-
tically)", page 47).
Setting the Standard Bevel Angle 45° (Vertical)
– Bring the power tool into the table saw working position.
(see "Working Position", page 48)
– Turn the saw table 22 to the 0° detent 27. The lever 26
must be felt to engage in the detent.
– Loosen the lock lever 37 and tilt the tool arm leftward to
the stop (45°) by the handle 18.
Checking: (see figure
– Adjust an angle gauge to 45° and position it on the saw ta-
ble 22.
The leg of the angle gauge must be flush with the saw blade 7
over the complete length.
Adjusting: (see figure
– Loosen the nut (size 10 mm) of the Allen screw 58.
– Screw the Allen screw 58 with a suitable Allen wrench (size
3 mm) in or out until the leg of the angle gauge is flush with
the saw blade over the complete length.
– Retighten the nut again.
In case the angle indicator 47 is not in a line with the 45° mark
of the scale 48, firstly check the 0° setting for the bevel angle
and the angle indicator again. Then repeat the adjustment of
the 45° bevel angle.
Setting the Standard Bevel Angle 33.9° (Vertical)
– Bring the power tool into the table saw working position.
(see "Working Position", page 48)
– Turn the saw table 22 to the 0° detent 27. The lever 26
must be felt to engage in the detent.
– Loosen the lock lever 37.
– Push the stop bolt 33 completely inside and swivel the tool
arm until the bolt faces against the stop screw 32.
Checking: (see figure
– Adjust an angle gauge to 33.9° and position it on the saw
table 22.
The leg of the angle gauge must be flush with the saw blade 7
over the complete length.
Adjusting: (see figure
– Loosen the nut (size 10 mm) of the stop screw 32.
– Screw the stop screw with a suitable spanner (size 10 mm)
in or out until the leg of the angle gauge is flush with the saw
blade over the complete length.
– Retighten the nut again.
English | 47
Q2)
R1)
R2)
S1)
S2)
1 609 92A 3S7 | (24.2.17)