Creating A New Playlist; Editing Playlists - Pioneer HD-V9000 Mode D'emploi

Creating a new playlist

07
1 Display the Setup menu.
Press SETUP.
Select Playlist  Create/Edit  Select.
2
Use /// to select, then press ENTER. The basic
playlist creation screen appears.
• If not a single line is registered, press the  button to
proceed to step 4.
3 Add a playlist.
Press ENTER. The command selection screen appears.
Use / to select Create List, then press ENTER. A new
playlist with the highest number is created.
4 Select the line number.
Use  to select 01.
5 Set the type of playback.
Press , select Type Select, then press ENTER. The
settings screen appears. Use / to select the setting,
then press ENTER. For details on the settings, see
page 58.
6 Select the file to be played.
Use  to select File Select, then press ENTER. The file
selection screen appears. Use / to select the file, then
press ENTER.
7 Set the details for playback.
Press , select Property, then press ENTER. The details
settings screen appears. Use /// to change the
settings, select OK, then press ENTER. For details on the
contents of the settings, see Property under Type Select
setting on page 58.
Create/Edit
01 Fileplay
Property
List 01
Audio
List 02 0
Video
List 03
0 Audio Adjust
Lip Sync
0
Lip Sync Adjust :
Start
0
End
OK
Move Select
• Once registration of a line is completed, Type Select
appears on the next line. Use / to select the next
line, then repeat steps 5 to 7.
8 Finish creating the playlist.
When SETUP or RETURN is pressed, a confirmation
screen appears. Use / to select OK, then press
ENTER. The playlist settings are saved.
• When the SETUP button is pressed, the Setup screen
turns off.
• When RETURN is pressed, the unit returns to step 2.
• When CANCEL is selected, the unit returns to step 2
without saving the playlist settings.
• When RETURN is selected, the unit returns to the
56
previous step.
En
Playlist
UsedList [01/20] Used Memory [
***
LLLLLLLLLL.mp
Property
: Off
: On
: +00 [dB]
: Off
+00 [Frame]
:
h m s
0 0 0 0 0 0
:
h m s
0 0 0 0 0 0
ENTER Return RETURN Exit SETUP
Note
• Up to 20 playlists can be registered.
• Up to 12 video files can be registered per playlist.
• The amount of memory used depends on the number
of files, playing time and type of playback. It is not
possible to set a playlist if the amount of memory
used exceeds 100%.
• The playback operation and file must be selected for
line registration to be completed.
• Video files for which there is no time map table file
cannot be registered.

Editing playlists

Use this procedure to edit existing playlists.
1 Display the Setup menu.
Press SETUP.
Select Playlist  Create/Edit  Select.
2
Use /// to select, then press ENTER. The basic
playlist creation screen is displayed.
3 Select the playlist.
Use / to select, then press .
4 Select the line you want to edit.
Use / to select.
5 Select the item you want to edit.
Use / to select, then press ENTER.
• When the line number is selected, the line editing
command selection screen appears. For details on
the contents of the settings, see page 59.
• When Type Select is selected, the Type Select
selection screen appears. For details, see page 58.
% ]
• When a file name is selected, the file selection screen
appears.
• When Property is selected, the details settings
screen appears. For details on the contents of the
settings, see pages 58 to 61.
6 Change the setting.
Use /// to change the settings, then press
ENTER.
7 Finish editing the playlist.
When SETUP or RETURN is pressed, a confirmation
screen appears. Use / to select OK, then press the
ENTER button. The playlist settings are saved.
• When SETUP is pressed, the Setup screen turns off.
• When RETURN is pressed, the unit returns to step 3.
• When CANCEL is selected, the unit returns to step 2
without saving the playlist settings.
• When RETURN is selected, the unit returns to the
previous step.