Scheppach 5903702901 Traduction Du Manuel D'origine page 20

GB
4) Power tool use and care
a) Do not force the power tool. Use the cor-
rect power tool for your application. The
correct power tool will do the job better and
safer at the rate for which it was designed.
b) Do not use the power tool if the switch
does not turn it on and off. Any power tool
that cannot be controlled with the switch is
dangerous and must be repaired.
c) Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such
preventive safety measures reduce the risk of
starting the power tool accidentally.
d) Store idle power tools out of the reach of
children and do not allow persons unfa-
miliar with the power tool or these instruc-
tions to operate the power tool. Power tools
are dangerous in the hands of untrained us-
ers.
e) Maintain power tools. Check for misalign-
ment or binding of moving parts, breakage
of parts and any other condition that may
affect the power tool's operation. If dam-
aged, have the power tool repaired before
use. Many accidents are caused by poorly
maintained power tools.
f) Keep cutting tools sharp and clean. Prop-
erly maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to
control.
g) Use the power tool, accessories and tool
bits etc. in accordance with these instruc-
tions, taking into account the working con-
ditions and the work to be performed. Use
of the power tool for operations different from
those intended could result in a hazardous
situation.
5) Service
a) Have your power tool serviced by a quali-
fied repair person using only identical re-
placement parts. This will ensure that the
safety of the power tool is maintained.
ADDITIONAL SAFETY INSTRUCTIONS FOR
ABRASIVE CUTTING-OFF OPERATIONS
CUT-OFF MACHINE SAFETY WARNINGS
a) The guard provided with the tool must be
securely attached to the power tool and po-
sitioned for maximum safety, so the least
amount of wheel is exposed towards the
operator. Position yourself and bystanders
away from the plane of the rotating wheel.
The guard helps to protect operator from broken
wheel fragments and accidental contact with
wheel.
20 І 52
 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58
b) Use only bonded reinforced or diamond Cut-
ting wheels for your power tool.
Just because an accessory can be attached to
your power tool, it does not assure safe opera-
tion.
c) The rated speed of the accessory must be at
least equal to the maximum speed marked on
the power tool.
Accessories running faster than their rated speed
can break and fly apart.
d) Wheels must be used only for recommended
applications. For example: do not grind with
the side of Cutting wheel.
Abrasive Cutting wheels are intended for periph-
eral grinding, side forces applied to these wheels
may cause them to shatter.
e) Always use undamaged wheel flanges that
are of correct diameter for your selected
wheel.
Proper wheel flanges support the wheel thus re-
ducing the possibility of wheel breakage.
f) Do not use worn down reinforced wheels
from larger power tools.
Wheels intended for a larger power tool are not
suitable for the higher speed of a smaller tool and
may burst.
g) The outside diameter and the thickness of
your accessory must be within the capacity
rating of your power tool. Incorrectly sized
accessories cannot be adequately guarded
or controlled.
h) The arbour size of wheels and flanges must
properly fit the spindle of the power tool.
i) Wheels and flanges with arbour holes that
do not match the mounting hardware of the
power tool will run out of balance, vibrate ex-
cessively and may cause loss of control. Do
not use damaged wheels. Before each use,
inspect the wheels for chips and cracks. If
power tool or wheel is dropped, inspect for
damage or install an undamaged wheel. After
inspecting and installing the wheel, position
yourself and bystanders away from the plane
of the rotating wheel and run the power tool
at maximum no load speed for one minute.
Damaged wheels will normally break apart
during this test time.
j) Wear personal protective equipment. De-
pending on application, use face shield, safe-
ty goggles or safety glasses. As appropriate,
wear dust mask, hearing protectors, gloves
and shop apron capable of stopping small
abrasive or workpiece fragments.
The eye protection must be capable of stopping
flying debris generated by various operations.
The dust mask or respirator must be capable of
filtrating particles generated by your operation.
Prolonged exposure to high intensity noise may
cause hearing loss.