Scheppach AB2000 Traduction De La Notice Originale page 21

ATTENTION
A damaged dust cap must be replaced immediately. It
is recommended to have this done by a service centre.
1. Pull the locking sleeve (1b) backwards to unlock the
tool receiver (1).
2. Insert the tool attachment (6/7) into the tool receiver
(1) by turning it.
Ensure that the tool attachment (6/7) is correctly en-
gaged in the tool receiver (1).
3. Release the locking sleeve (1b).
4. Check the tool attachment (6/7) is seated firmly by
pulling on it.
The tool attachment (6/7) has some radial play due to
the system.
8.2 Removing the flat chisel (6) or
pointed chisel (7) (Figs. 3)
1. Pull the locking sleeve (1b) backwards and remove
the tool attachment (6/7).
8.3 Adjusting the additional handle (2)
(Fig. 4, 5)
ATTENTION
Only use the product with the additional handle fitted.
Notes:
The additional handle can be rotated 360° on the product
and can be moved to any desired/needed position.
For your safety, the product must only be held by the han-
dle and the additional handle during operation. This pre-
vents electric shock when touching the lines.
1. Release the clamping screw (2a).
2. Position the additional handle (2) in a comfortable and
safe working position for you.
3. Re-tighten the clamping screw (2a).
9 Operation
WARNING
Danger of injury!
Do not insert the mains plug into the socket until you
are ready to use the product.
ATTENTION
Always make sure the product is fully assembled
before commissioning!
9.1 Selecting working position (Fig. 1)
Horizontal working position:
• Hold the additional handle (2) with your left hand and
the handle (5) with your right hand (for right-handed
users).
• Make sure you have a stable footing to safely absorb
the recoil.
Vertical working position:
• Hold the handle (5) firmly with both hands.
• Stand so that you can guide the tool attachment
straight down, and use the weight of the product for
the work.
Note:
Only work with moderate pressure to maximise impact
absorption.
9.2 Switching the product on/off
(Fig. 1)
WARNING
Always make sure that the tool attachment is fitted cor-
rectly!
Switching on
1. Insert the mains plug into a properly fused mains
socket.
2. Press and hold the on/off switch (4).
Switching off
1. Release the on/off switch (4).
9.2.1
Switching on continuous operation
1. Press and hold the on/off switch (4).
2. Press the lock switch (4a).
3. Release the lock switch (4a) and the on/off switch (4).
Continuous operation is active.
Switching off continuous operation
1. Press the on/off switch (4) firmly to release the locking
switch (4a).
Continuous operation is stopped.
Wait until the product has come to a standstill before set-
ting it down.
9.3 Adjusting the speed
Note:
The speed can also be changed during operation.
You can preselect the speed using the speed control (4b):
1 = Lowest speed
6 = Highest speed
We recommend determining the speed using practical
tests.
The speed that makes sense when working depends on
what tasks you are doing with the product.
10 Electrical connection
The electrical motor installed is connected and ready
for operation. The connection complies with the ap-
plicable VDE and DIN provisions. The customer's
mains connection as well as the extension cable used
must also comply with these regulations.
• The product fulfils the requirements of EN 61000-3-11
and is subject to special connection requirements.
This means that use at any freely selectable connec-
tion points is not permitted.
• The product can cause temporary voltage fluctuations
in unfavourable mains conditions.
www.scheppach.com
Continuous operation (Fig. 1)
GB | 21