Technical Data; Attachment And Operation - Scheppach EMP-33 Traduction Des Instructions D'origine

• Do not use the device when barefoot, always
wear sturdy footwear.
• Make sure that the appliance cannot start up ac-
cidentally. Ensure that the electric tool is switched
off before you connect it to the power supply and/or
insert the battery, or pick up or carry the tool. If your
finger is on the switch whilst carrying the electric
tool or if you connect the appliance to the mains
when it is switched on, this can lead to accidents.
• Remove keys and wrenches before switching on
the electric tool. A tool or key which comes into
contact with rotating parts of the appliance can lead
to injuries.
• Avoid abnormal working postures. Make sure you
stand squarely and keep your balance at all times.
In this way, you can control the electric tool better
in unexpected circumstances.
• Do not operate the tool when barefoot or wea-
ring open sandals; always wear sturdy shoes and
long trousers
• Be familiar with the controls and the proper use
of the tool
• Never mow in the direct vicinity of persons (espe-
cially children) and animals
• Always keep hands and feet away from rotating
parts
• Keep away from the discharge opening at all
times
• Switch on the motor according to instructions and
with feet well away from the cutting blade
• This tool is not intended for use by persons (in-
cluding children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervi-
sion or instruction concerning use of the tool by a
person responsible for their safety (local regulati-
ons can restrict the age of the operator)
• Ensure that children do not play with the tool
• Operate the mower at a walking pace only (do
not run)
• Keep proper footing on slopes and do not mow
extremely steep slopes
• Be extremely careful when moving backwards or
pulling the mower towards you
5
Service
Have your electric tool repaired only by trained per-
•
sonnel using only genuine spare parts. This will
ensure that your electric tool remains safe to use.

6. Technical data

EMP-33
Technical data
Cutting data lawn mower
Cutting width mm
Cutting hight
adjustable mm
Collection bag
capacity l
20
 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58
310
30-45-60
28
Drive
Engine V / Hz
Enginespeed min -1
Power W
Wight kg
Subject to technical changes!
Information concerning noise emission measured
according to relevant standards:
Sound pressure L = 74 dB(A)
pA
Sound power L = 92 dB(A)
WA
Uncertainty K
= 3 dB(A)
PA
Wear ear-muffs.
The impact of noise can cause damage to hearing.
Vibration left hand A = 1,68 m/s
hv
Vibration right hand A = 1,55 m/s
hv
Uncertainty K
= 1.5 m/s 2
PA
Reduce noise generation and vibration to a minimum!
• Use only equipment that is in perfect condition.
• Maintain and clean the equipment regularly.
• Adopt your way of working to the equipment.
• Do not overload the equipment.
• Have the equipment checked if necessary.
• Switch off the equipment when not in use.
• Wear gloves and ear protection.
In these operating instructions we have marked
the places that have to do with your safety with
m
this sign:

7. Attachment and operation

ATTENTION! Before working on the device - cleaning,
inspection, maintenance or other work - always turn off
the device and separate it from the power supply.
ASSEMBLY
Attaching the wheels Fig. 1
• Turn the lawn mower over and attach the 4
wheels to the lawn mower with the 4 screws.
Use the Allen key for this.
• You can attach the wheels at 3 different heights
(cutting height 30/45/60 mm).
Make sure all 4 wheels are attached at the
same height.
Attaching the handles Fig 2
• Insert the bottom tubular frame in the hole in
the lawnmower and secure it with 2 screws.
• Bolt the top tubular frame with the lower frame
using the 2 screws, 2 washers and 2 wing nuts.
Fastening the cable to the handle
• Fasten the loose cable to the top tubular frame
with the aid of the cable ties. (Fig. 2)
230 / 50
2850
1000
10
2
2