Switching On And Off - Elem Garden Technic CBE5530T Traduction Des Instructions D'origine

INSTRUCTIONS FOR USE
Remove stones, loose pieces of
wood and other objects from the
The cutting line continues to rotate for a few seconds
after the trimmer is switched off. Allow the
motor/cutting line to stop rotating before switching
"on" again.
Do not rapidly switch off and on.
_ Connect the appliance to a suitable extension
cord.
_ Hook the extension cord behind the clamp.
_ Hold the appliance with both hands.
_ Slowly move the appliance back and forth.
_ When working long grass proceed layer
for layer.
_ Keep the appliance away from hard
objects and plants.
_ Only use the appliance for working dry
grass.
_ The appliance will automatically feed the
cutting line during use.

SWITCHING ON AND OFF

If the trimmer is to be used for the first time, check
that the nylon line touches or passes over the
cutting blade. The nylon line will be cut
automatically when turn on the switch to the
maximum length. If it does not reach the necessary
length, push the head of spool with your finger while
pulling the lines .
Insert the plug into the extension cable and attach it
to the handle. Pressure the switch and make the
trimmer turn at no load; thus, the line length is
automatically adjusted. Only approach the
implement to the grass to be cut while it is in
operation, i.e. while the switch is pressed down.
Caution! Before turn on the switch, take the
blade cover away.
To cut long grass, take several small cuts. Never cut
wet or very damp grass. The line has to be
protected against premature wear caused by hard
obstacles; for this purpose, keep the trimmer away
from hard surfaces using the guard's edge as a
protection. A short or worn line will reduce cutting
capacity. So, to restore the line to its optimum
length, push the implement to the ground while it is
running; this way, the line will automatically be the
correct length .
CAUTION! The short or worn line cuts less
efficiently therefore, to improve its operations,
unplug the electrical supply and repeat the
operation described in the beginning of the chapter.
These make sure that everything is functioning
properly and to familiarize yourself with the grass
trimmer.
CAUTION! After switching off, the nylon line will
continue to rotate for a few more seconds.
cutting area.
REPLACEMENT OF THE LINE SPOOL
Unplug from the socket.

Turn upside down the machine with the guard

facing upwards.
Hold with one hand the motor fan firmly and

with the other hold the spool holder. Push the
clips of the spool holder both side down and
pull it out of the motor fan.
Extract the empty spool and clean the inside of

the spool holder carefully removing all dust
and grass residues.
Insert now the new spool in the motor fan and

push the end of line through the lateral holes
provided on the motor fan.
Push the spool holder on and fasten it

securely.
Re-establish the length of the nylon line by

pushing the head of spool holder and pull the
line ends out to the desired length (approx. 10
cm).
CAUTION! Under no circumstances wind extra line
on the empty spool but instead replace it with a new
one, the same as the original. The use of line with
different characteristics to those of the original can
permanently damage the grass trimmer as well as
annulling the terms of the guarantee.
INSTRUCTIONS
after reading the safety instructions, carefully follow
the instructions below to get the most from your
trimmer.
start slowly, once you have gained experience, you
will be able to use the full potential of the edger.
start the trimmer before getting near the grass to
cut.
cut the grass by moving the trimmer from right to
left and proceed slowly keeping the inclined edger
about 15 °.
the tall grass should be cut in layers, always starting
at the top. the cuts should be short.
do not cut wet or damp grass. dry grass gives
excellent results.
always leave nylon thread run at the maximum
speed; not working so overload the trimmer.
warning! do not use the trimmer without the
protection.
never run the edger on the extension cable while
the trimmer is in operation; make sure the cable is
always safe behind your back.
before starting work, check that the cutting area is
free of stones, debris, son and other objects...
26