Frames Of Information On The Product Configuration - ADEUNIS sigfox RC1 Pulse Guide Utilisateur

sigfox RC1 Pulse - Guide utilisateur / User guide version V2.0.2

4.1.2 Frames of information on the product configuration

Following reception of a downlink frame with the code 0x01 or on switching to the operating mode (from the Park or Command Mode), the
following frames (0x10, 0x11 et 0x12) representing the application configuration of the product are transmitted:
0 1
Code Status
0x10 Cf Status
0x10 0xA3
Description of the frame:
• Byte 2 : register 306, product mode (Park, Standard (production), Test or REPLI)
• Byte 3 : register 301, periodicity of transmission (periodic mode), expressed in minutes
EN
• Byte 4 : register 320, channels configuration (A and B)
• Byte 5 : register 321, history configuration (channels A and B)
• Byte 6 : register 322, anti-bounce filter period (channels A and B)
• Bytes 7 and 8 : register 325, flow calculation period (x1 minute if S306=1, x20 seconds if S306=2)
In the example in grey this gives:
• Byte 2 : S306=0x01: PRODUCTION mode in progress
• Byte 3 : S301=0x06 = 60 (decimal): transmission period is set to 60 minutes.
• Byte 4 : S320 = 0x39 : channels configuration (A and B) :
• Channel A :
- Activated
- Meter other than gas
- Tamper input activated
• Channel B :
- Activated
- Gas meter
- Tamper input deactivated
• Byte 5 : S321=0x02, history configuration: channels A and B : history mode with recording of counters every hours and sending every 24h
so 24 values by meter
• Byte 6 : S322=0x57, anti-bounce channel A = 500ms and channel B = 100ms
• Bytes 7 and 8 : register 325=0x003C=60 (decimal), flow calculation period is set to 60min
0
Code
0x11 Cf Status
0x11
Description of the frame:
• Bytes 2 and 3 : register 326, flow threshold (channel A)
• Bytes 4 and 5 : register 327, flow threshold (channel B)
• Bytes 6 and 7 : register 328, leak threshold (channel A)
• Bytes 8 and 9 : register 329, leak threshold (channel B)
In the example in grey this gives:
• Bytes 2 and 3 : S326=0x2710=10 000 (decimal), flow threshold for channel A is to 10,000 pulses per hour
• Bytes 4 and 5 : S327=0x7530=30 000 (decimal), flow threshold for channel B is to 30,000 pulses per hour
• Bytes 6 and 7 : S328=0x000A=10 (decimal), leak threshold for channel A is to 10 pulses per hour
• Bytes 8 and 9 : S329=0x0000, leak threshold for channel B is to 0 pulse per hour
0
Code Status
0x12 Cf Status
0x12 0xA3
2 3
S306 S301
0x01 0x06
1 2 - 3
Status
S326
0xA3 0x2710
1 2 - 3
PAYLOAD
S330
0x0003
4 5
PAYLOAD...
S320 S321
0x39 0x02
4 - 5 6 - 7
PAYLOAD
S327 S328
0x7530 0x000A
4 - 5
S331
0x0005
6 7 - 8
S322 S325
0x57 0x003C
8 - 9
S329
0x0000
Page 82 of 104