Declaration Of Conformity; Battery Charging - Bosch ANGLE EXACT ION 8-1100 Notice Originale

OBJ_BUCH-1521-005.book Page 18 Tuesday, February 24, 2015 2:30 PM
18 | English
Article number 0 607 ...
Maximum torque, hard screw-
driving application according to
ISO 5393
Tightening torque at the flange
Accessories for
ANGLE EXACT ION
Weight according to
EPTA-Procedure 01/2003

Declaration of Conformity

We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with all rele-
vant provisions of the directives 2009/125/EC (Regulation
1194/2012), 2011/65/EU, until 19 April 2016:
2004/108/EC, from 20 April 2016 on: 2014/30/EU,
2006/42/EC including their amendments and complies with
the following standards: EN 60745-1, EN 60745-2-2.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
70764 Leinfelden-Echterdingen, GERMANY
Henk Becker Helmut Heinzelmann
Executive Vice President Head of Product Certification
Engineering PT/ETM9
Robert Bosch GmbH, Power Tools Division
70764 Leinfelden-Echterdingen, GERMANY
Leinfelden, 24.02.2015
Assembly
 Before any work on the power tool, remove the battery.

Battery Charging

 Use only the battery chargers recommended by Bosch
for this power tool. Only these battery chargers are
matched to the lithium ion battery used in your machine.
Note: The battery supplied is partially charged. To ensure full
capacity of the battery, completely charge the battery in the
battery charger before using your power tool for the first time.
The lithium-ion battery can be charged at any time without re-
ducing its service life. Interrupting the charging procedure
does not damage the battery.
The lithium-ion battery is protected against deep discharging
by the "Electronic Cell Protection (ECP)". When the battery is
empty, the machine is switched off by means of a protective
circuit: The inserted tool no longer rotates.
 Do not continue to press the On/Off switch after the
machine has been automatically switched off. The bat-
tery can be damaged.
Observe the notes for disposal.
1 609 92A 138 | (24.2.15)
Angled drive head
1/4" 3/8"
... 453 617 ... 453 620 ... 451 618 ... 453 618 ... 453 630 ... 453 631
Nm 20 25
Nm 20 20
15-500 15-500
kg 0.2 0.2
Removing the battery (see figures A1 – A2)
The battery 9 is equipped with two locking levels that should
prevent the battery from falling out when pushing the battery
unlocking button 14 unintentionally. As long as the battery is
inserted in the power tool, it is held in position by means of a
spring.
– To remove the battery 9, press the unlocking button 14
and pull out the battery toward the front. Do not exert any
force.
Battery Charge-control Indication (yellow LED)
Battery Charge-
control Indica-
tion 8
Flashing light +
audio signal
Continuous light Capacity no longer sufficient for a new
Flashing light
Operating and Storage Environment
The device is suitable exclusively for operation at enclosed
work sites.
For proper operation, the allowable ambient temperature
should be between 0 °C und +45 °C at an allowable relative
humidity between 20 and 95 %, free of moisture condensa-
tion.
Suspension Device (see figure B)
With the utility clip 15, the machine can be attached to a sus-
pension device.
– Fasten the utility clip 15 to the machine by engaging it into
the fastening slots 16.
3/8"
1/4" QC 1/4"
30 20 20
25 20 20
30-300 15-500 15-500
0.3 0.2 0.2
Meaning
Battery Charging:
Only 6–8 more screwdriving operations
possible.
screwdriving operation or the machine
was subject to overload:
The machine can no longer be switched
on.
– Remove the battery and replace with
a fully charged one.
The machine is overheated and out of
operation:
– Before restarting the operation of the
machine, wait until the flashing auto-
matically stops after a short period.
Straight
drive head
QC 1/4"
6
10
15-500
0.2
Bosch Power Tools