Additional Safety Rules - Ryobi EMS-1121L Manuel D'utilisation

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 1
GB
F
D
RULES FOR SAFETY OPERATION
WARNING!
When using electric tools, basic safety
precautions, including the following, should
always be followed to reduce the risk of fire,
electric shock and personal injury. Read and
understand and these instructions before
operating this product and save these
instructions.
KEEP WORK AREA CLEAN. Cluttered areas and
benches invite injuries.
CONSIDER WORK AREA ENVIRONMENT. Do not
expose power tools to rain. Do not use power tools in
damp or wet locations. Keep work area well lit. Do not
use power tools where there is risk to cause fire or
explosion.
GUARD AGAINST ELECTRIC SHOCK. Avoid body
contact with earthed or grounded surfaces (e.g.
pipes, radiators, ranges, refrigerators, other metal
surfaces).
KEEP CHILDREN AWAY. Children and pets should
be kept at a safe distance from the work area.
STORE IDLE TOOLS. When not in use, tools should
be stored in a dry, high or locked up place, out of
reach of children.
DO NOT FORCE THE TOOL. It will do the job better
and safer at the rate for which it was intended.
USE THE RIGHT TOOL. Do not force small tools or
attachments to do the job of a heavy-duty tool. Do not
use tools for purposes not intended.
DRESS PROPERLY. Do not wear loose clothing or
jewellery, they can be caught in moving parts. Rubber
gloves and non-skid footwear are recommended
when working outdoors. Wear protecting hair
covering to contain long hair.
USE SAFETY GLASSES.
Use face or dust mask if the cutting
operation is dusty. Also use ear
protection to reduce the risk of induced
hearing loss.
SECURE WORK. Use clamps or a vice to hold the
work. It is safer than using your hand and it frees both
hands to operate the tool.
DO NOT OVERREACH. Keep proper footing and
balance at all times.
SWITCH TRIGGER. Avoid accidental starting, be
sure the switch trigger is in the locked or OFF position
after use.
E
I
P
NL
S
DK
N
FIN
English
MAINTAIN TOOLS WITH CARE. Keep cutting tools
sharp and clean for better performance. Follow
instructions for lubrication and changing accessories.
Inspect tool cord periodically and if damaged have it
repaired by an authorised service facility. Inspect
extension cords periodically and replace if damaged.
Keep handles dry, clean and free from oil and grease.
STAY ALERT. Watch what you are doing at all times.
Use common sense. Do not operate tool when you
are tired or under the influence of drugs or alcohol.
CHECK DAMAGED PARTS. Before further use of
the tool, a guard or other part that is damaged should
be carefully checked to determine that it will operate
properly and perform its intended function. Check for
alignment of moving parts, free running of moving
parts, breakage of parts and any other conditions that
may affect its operation. A guard, or other part, that is
damaged should be properly repaired or replaced by
an authorised service centre.
Have defective switches replaced by an authorised
service facility. Do not use the tool if the switch does
not turn it on and off.
ACCESSORIES. Only use accessories that are
recommended by the manufacturer, other
accessories may create a risk of injury when used on
this tool.
WARNING!
The use of any accessory or attachment, except
those recommended in this instruction manual
and from other recognised accessory suppliers,
may present a risk of personal injury.
HAVE YOUR TOOLS REPAIRED BY A QUALIFIED
PERSON. This electric tool is manufactured in
accordance with the relevant safety requirements.
Repairs should only be carried out by qualified
persons using original spare parts, otherwise this may
result in considerable danger to the user.

ADDITIONAL SAFETY RULES

Always remove the plug from the mains socket before
making any adjustments or maintenance, including
changing the blade.
When operating the saw, use safety equipment
including safety goggles or shield, ear protection, dust
mask and protective clothing including safety gloves.
Ensure that there is adequate general or localised
lighting.
Do not use the saw unless the guards are in place.
9
GR
H
CZ
RUS
RO
PL

Publicité

Table des Matières
loading

Table des Matières