Ryobi ETS-1825 Manuel D'utilisation page 18

ETS-1825 manual 17/06/04
GB
F D E
ADDITIONAL SAFETY RULES FOR CIRCULAR
SAW BENCH
ALWAYS use a push stick for ripping narrow stock.
■
Refer to ripping applications in instruction manual
where Push stick is covered in detail. See push stick
pattern Included in this instruction manual.
NEVER perform any operation "free-hand" which
■
means using your hand to support or guide the
workpiece. Always use either the fence or the miter
gauge to position and guide the work.
NEVER Stand or have any part of your body in line
■
with the path of the saw blade. KEEP your hands out
of the line of the saw blade.
NEVER reach behind or over the cutting tool with
■
either hand for any reason.
MOVE the rip fence out of the way when cross-cutting.
■
NEVER use the fence as a cut-off gauge when
■
cross-cutting.
DIRECTION OF FEED. Feed work into a blade or
■
cutter against the direction of rotation of the blade or
cutter only.
NEVER attempt to free a stalled saw blade without
■
first turning the saw OFF. Turn off switch immediately
to prevent motor damage.
PROVIDE adequate support to the rear and sides of
■
the saw table for wide or long work pieces.
AVOID KICKBACKS (work thrown back toward you) by:
■
(1) Keeping blade sharp.
(2) Keeping rip fence parallel to the saw blade.
(3) Keeping splitter and guard in place and operating.
(4) Not releasing the work before it is pushed all the
way past the saw blade.
(5) Not ripping work that is twisted or warped or does
not have a straight edge to guide along the fence.
AVOID awkward operations and hand positions
■
where a sudden slip could cause your hand to move
into the cutting tool.
NEVER use solvents to clean plastic parts. Solvents
■
could possibly dissolve or otherwise damage the
material. Only a soft damp cloth should be used to
clean plastic parts.
PERMANENTLY mount the saw to a supporting
■
surface before performing any cutting operations.
NEVER cut metals or materials which may make
■
hazardous dust.
ALWAYS use in a well ventilated area. Remove saw
■
dust frequently. Clean out sawdust from the interior of
the saw to prevent a potential fire hazard.
13:04 Page 11
I P NL S DK
English
■
■
■
■
■
■
■
■
■
■
■
■
■
■
SPECIFICATION
Rated voltage
Rated input
Rated current
No load speed
Arbor
Saw blade diameter
11
N FIN GR H CZ
Do not use saw blades which are damaged or
deformed.
Replace table insert when worn.
Use only saw blades recommended by the
manufacturer.
Warning
The splitter shall not be thicker than the kerf of
blade and not thinner than the body of saw blade.
Take care that the selection of the saw blade depends
on the material to be cut. Use only saw blades for
which the maximum possible speed is not less than the
maximum speed of the tool and the material to be cut.
Do not use high speed steel (HSS) blade.
Use this circular saw to cut only wood and wood
like products.
Use push-sticks to feed the workpiece past the blade.
Always store the push stick with the machine when
not in use.
Connect saw to a dust-collecting device when sawing.
Store idle tools. When not in use, tools should be stored
in a dry locked-up place, out of reach of children.
Connect dust extraction equipment. If device are
provided for the connection of dust extraction and
collecting equipment ensure these are connected and
properly used.
Do not abuse the cord. Never yank the cord to
disconnect it from the socket. Keep the cord away
from heat, oil and sharp edges.
Stay alert. Watch what you are doing, use common
sense and do not operate the tool when you are tired.
Inspect tool cords periodically and if damaged have
them repaired at an authorized service facility. Inspect
extension cord periodically and replace if damaged.
Have your tool repaired by a qualified person.
This electric tool complies with the relevant rules.
Repairs should only be carried out by qualified
persons using original spare parts, otherwise this may
result in considerable danger to the user.
Use outdoor extension leads. When the tool is used
outdoors, use only extension cords intended for
outdoor use and so marked.
110 V / 230 V ~ 50 Hz
1800 W
7.5 A
4800 min
30 mm
250 mm
RUS RO PL
-1