Safety Rules - Ryobi ETS-1825 Manuel D'utilisation

ETS-1825 manual 17/06/04
GB
F D E

SAFETY RULES

FOR YOUR OWN SAFETY, READ INSTRUCTION
■
MANUAL BEFORE OPERATING THE TOOL.
Learn the tool's application and limitations as well as
the specific hazards peculiar to it.
KEEP GUARDS IN PLACE and in working order.
■
GROUND ALL TOOLS. If tool is equipped with
■
threeprong plug, it should be plugged into a three-
hole electrical receptacle. If an adapter is used to
accommodate a two-prong receptacle, the adapter
plug must be attached to a known ground. Never
remove the third prong.
REMOVE ADJUSTING KEYS AND WRENCHES.
■
From habit of checking to see that keys and adjusting
wrenches are removed from tool before turning it "ON".
KEEP WORK AREA CLEAN. Cluttered areas and
■
benches invite accidents.
DON'T USE IN DANGEROUS ENVIRONMENT.
■
Don't use power tools in damp or wet locations,
or expose them to rain. Keep work area well lit.
KEEP CHILDREN AND
■
All children and visitors should be kept a safe
distance from work area.
MAKE WORKSHOP CHILDPROOF with padlocks,
■
master switches.
DON'T FORCE TOOL. It will do the job better and be
■
safer at the rate for which it was designed.
USE RIGHT TOOL. Don't force tool or attachment to
■
do a job for which it was not designed.
WEAR PROPER APPAREL. No loose clothing, rings,
■
gloves, neckties, bracelets, or jewelry to get caught in
moving parts. Non-slip footwear is recommended.
Wear protective hair covering to contain long hair.
ALWAYS WEAR
■
PROTECTIVE EQUIPMENT,
(1) Wear safety glasses. (2) Hearing protection.
(3) Respiratory protection (4) Wear gloves when
handling saw blades and rough material. Saw blades
shall be carried in a holder whenever practicable.
SECURE WORK. Use clamps or a vise to hold work
■
when practical. It's safer than using your hand and
frees both hands to operate tool.
DON'T OVERREACH. Keep proper footing and
■
balance at all times.
MAINTAIN TOOLS IN TOP CONDITION. Keep tools
■
sharp and clean for best and safest performance.
Follow instructions for lubricating and changing
accessories.
13:04 Page 10
I P NL S
English
VISITORS AWAY.
SUITABLE PERSONAL
INCLUDING
10
DK N FIN GR H
DISCONNECT TOOLS before servicing and when
■
changing accessories such as blades, bits, cutters, etc.
USE RECOMMENDED ACCESSORIES. The use of
■
improper accessories may cause hazards.
AVOID ACCIDENTAL STARTING. Make sure switch
■
is in "OFF" position before plugging in power cord.
NEVER STAND ON TOOL. Serious injury could
■
occur if the tool is tipped or if the cutting tool is
accidentally contacted.
CHECK DAMAGED PARTS. Before further use of
■
the tool, a guard or other part that is damaged should
be carefully checked to ensure that it will operate
properly and perform its intended function – check for
alignment of moving parts, binding of moving parts,
breakage of parts, mounting, and any other part that
is damaged should be properly repaired or replaced.
DIRECTION OF FEED. Feed work into a blade or
■
cutter against the direction of rotation of the blade
or cutter only.
NEVER LEAVE TOOL RUNNING UNATTENDED.
■
TURN POWER OFF. Don't leave tool until it comes to
a complete stop.
DRUGS, ALCOHOL, MEDICATION. Do not operate
■
tool while under the influence of drug, alcohol or
any medication.
MAKE SURE TOOL IS DISCONNECTED FROM
■
POWER SUPPLY while motor is being mounted,
connected or reconnected.
WARNING
The dust generated by certain woods and wood
products can be injurious to your health. Always
run machine in well ventilated areas and provide
for proper dust removal. Use dust collection
systems when sawing.
ADDITIONAL SAFETY RULES FOR CIRCULAR
SAW BENCH
WARNING
When using electric tools basic safety precautions
should always be followed to reduce the risk of
fire, electrical shock and personal injury: read all
these instructions before attempting to operate
this product and save these instructions.
ALWAYS use guard and splitter on all "thru-sawing"
■
operations. Thru-sawing operations are those when
the blade cuts completely through the work piece as
in ripping or cross-cutting.
ALWAYS hold the work firmly against the miter gauge
■
of fence.
CZ RUS RO PL