Assembling The Grass Trimmer; Proper Use; Before Starting - EINHELL ROYAL RT 551 Mode D'emploi

Anleitung RT 551 SPK 7

5. Assembling the grass trimmer

Plug the guard hood on the motor head and
fasten with the supplied screws (see Figure 3).
First fasten the screws shown in Figure 4, then
you can fasten the two screws in conjunction
with the edge guide (see Figure 5).
Fit the handle as shown in Figure 6.

6. Proper use

The trimmer is designed for cutting lawns and small
areas of grass in private and hobby gardens.
Tools for private and hobby gardens are not suitable
for use in public facilities, parks and sport centers,
along roadways, on farms or in the forestry sector.
For the tool to be used properly it is imperative to
follow the instructions set out in the manufacturer's
directions for use.
Important! It is prohibited to use the tool to chop
material for composting because of the potential
danger to persons and property.

7. Before starting

You can adjust the height of the grass trimmer and
the position of the auxiliary handle to obtain the
optimal working position.
Height adjustment:
Turn the height adjuster (Figure 8 Item 1) clockwise
(see arrow) and set the required height. Turn the
height adjuster anti-clockwise again to secure it.
Adjusting the position of the auxiliary handle:
Rest the grass trimmer firmly on the ground. Slacken
the screw (Figure 7 / Item 1) and move the auxiliary
handle to the optimal position. Tighten the screw to
fix the handle in place.
Adjusting the tilt of the handle
Rest the grass trimmer firmly on the ground. Press
with you foot on the pedal on the side of the motor
housing (Figure 17). You can now adjust the handle
to the required angle of tilt (Figure 17). To fix the
handle at this angle, let go of the pedal and allow to
handle to latch home.
8. To start
The grass trimmer is designed only to cut grass.
The grass trimmer has a semi-automatic line
extension system. Each time you activate the semi-
automatic line extension system, the line will be
extended to ensure that you can cut your lawn with
the perfect cutting width at all times.
22.10.2003 8:00 Uhr Seite 13
Please note that the wear on the line will be
increased if you activate the semi-automatic line
extension system frequently.
Note
If the line is too long when you use the machine
for the first time, the surplus end of it will be cut
by the blade on the safety hood.
If the line is too short when you start the machine
for the first time, press the knob on the line spool
and pull the line hard. When you then start the
machine for the first time the line will be cut to
the perfect length automatically.
Your grass trimmer will work at its best if you
observe the following instructions:
Never use the grass trimmer without its safety
devices.
Do not cut grass when it is wet. The best results
are had on dry grass.
Connect the power cable to an extension cable
and hook the extension cable on the handle
(Figure 9).
To switch on your grass trimmer press the safety
lock-off (Figure 1 Item 4) and then press the
ON/OFF switch (Figure 1 Item 3).
To deactivate the grass trimmer, let go of the
On/Off switch (Figure 1 / Item 3).
Do not move the grass trimmer against the grass
until the switch is pressed, i.e. wait until the
trimmer is running.
For the correct cutting action, swing the grass
trimmer to the side as you walk forward, holding
it at an angle of approx. 30° as you do so (see
Figure 10 and Figure 11).
Make several passes to cut long grass shorter
step by step from the top (see Figure 12).
Make full use of the edge guide and the guide
hood in order to avoid unnecessary line wear .
Keep the grass trimmer away from hard objects
in order to avoid unnecessary line wear.
9. Using the grass trimmer as an edge
cutter
The grass trimmer can be adapted in the following
way to cut the edges of lawns and flower beds:
Disconnect the grass trimmer from the power
supply!
Turn the bar on the height adjuster (Figure 8
Item 1) through 180° clockwise (/see arrow) until
it reaches the stop.
The grass trimmer has now been converted into
GB
13