Publicité
EN
TABLE OF CONTENTS
1
Safety warnings
2
Product introduction
2.1
Product description
2.2
Technical specifications
2.3
Wiring table
2.4
Mounting surface materials
2.5
Assembly equipment
2.6
Safety distances
2.7
Hazards and risks
3
Preliminary Checks
4
Installation dimensions
4.1
Commercial profile installation dimensions - Side View
4.2
Dimensions of installation with glass panels - Side View
4.3
Installation with breakout profile
5
Fixing instructions
5.1
Locking
5.2
Inserting the track on the beam
5.3
Double panel installation dimensions - Top and front view
5.4
Installation dimensions of single panel version with
opening to the right - Top and front view
5.5
Installation dimensions for single panel version with
opening to the left - Top and front view
6
Panel preparation
6.1
Detail of the runner
6.2
Assembly of the runners on the panel with lowered
adapter profile
6.3
Fixing of the runner on the adapter profile
6.4
Inserting the panel on the beam
6.5
Fastening the guide to the floor and sliding runner
7
Positioning and wiring the modules
7.1
Positioning of the modules inside the beam
7.2
Wiring of the modules inside the beam
7.3
Connection of the panel to the transmission belt
7.4
Tensioning the belt
7.5
Adjusting the limit switches
7.6
Wiring of the door to the line
8
Installation of protection panels
8.1
Assembly of lateral compartments
8.2
Recessed wall beam
8.3
Cover panel preparation
8.4
Locking the cover panel
2
9
pag. 3
Control unit
9.1
The board
9.2
CTLEV control equipment
pag. 5
9.3
Example of sensor connection
pag. 5
9.4
Example of sensor connection conforming to EN16005
pag. 5
9.5
Example of PA025CT, OP2 and OP3 connection
pag. 5
9.6
Example of PA025CT, OP2 and OP3 monitored connection
pag. 6
9.7
Example of SMNPAE manual selector connection
pag. 6
9.8
Example of SEL1 and SEL2 connection
pag. 6
9.9
Example of SEL4 selector connection
pag. 7
9.10
First start-up
9.11
Power on
pag. 7
10
Operating mode
10.1
The operating modes
pag. 8
10.2
Learning procedure
pag. 8
10.3
Deceleration space self-test procedure
pag. 9
10.4
Bidirectional mode
pag. 9
10.5
Output Mode
10.6
Input Mode
pag. 10
10.7
Partial Opening Mode
pag. 10
10.8
Open Mode
pag. 10
10.9
Block Mode
pag. 11
10.10
Pharmacy Mode
10.11
Open and Close Commands
pag. 12
10.12
Start Command
10.13
Stop Command
pag. 13
10.14
Photo Command
10.15
Emergency opening command
10.16
RALL Photo command
pag. 14
10.17
Battery
pag. 14
10.18
No mains power supply
10.19
Interlock
pag. 14
10.20
Displays
pag. 14
pag. 15
11
pag. 15
Menu
11.1
Parameter modification procedure
11.2
Obstacle detection
pag. 16
11.3
Safety devices monitored
pag. 16
11.4
Settings with special codes
pag. 16
11.5
Examples of error codes
pag. 17
pag. 17
12
pag. 18
Maintenance plan
pag. 18
13
Testing and commissioning
pag. 18
13.1
Testing
pag. 18
13.2
Commissioning
pag. 19
pag. 19
pag. 20
pag. 21
pag. 21
pag. 22
pag. 23
pag. 24
pag. 25
pag. 25
pag. 26
pag. 26
pag. 27
pag. 27
pag. 28
pag. 28
pag. 28
pag. 28
pag. 28
pag. 28
pag. 29
pag. 29
pag. 29
pag. 29
pag. 29
pag. 29
pag. 29
pag. 29
pag. 29
pag. 29
pag. 30
pag. 30
pag. 30
pag. 30
pag. 30
pag. 31
pag. 32
pag. 32
pag. 33
pag. 33
pag. 33
pag. 34
pag. 35
pag. 36
pag. 36
pag. 36
Publicité
