EINHELL TC-SB 200/1 Instructions D'origine page 21

6. Assembly
CAUTION!
Pull out the power plug before carrying out any
maintenance, resetting or assembly work on the
bandsaw!
6.1.1 Fitting the rubber feet / tilt guard
(Fig. 5a/ 5b)
Secure the four rubber feet (49) to the bottom
side of the equipment using the screw (51), the
washer (43) and the nut (44).
Push the tilt guard (27) into the foot (5) and se-
cure it to the equipment using the socket head
screw (52), the washer (53) and the nut (54).
6.1.2 Mounting the saw table (Fig. 3 - 4)
•
Remove the web panel (4).
•
Place the saw table (15) onto the machine
housing from the rear. Secure the saw table
using the washers (55), the locking grip (18)
and the locking lever (56).
•
To dismantle, proceed in reverse order.
6.2. Tensioning the blade (Figure 1)
•
CAUTION! Remove the tension from the
blade if the bandsaw is not going to be used
for some time. Be sure to re-tension the blade
before you start the machine.
•
Turn the tightening screw (9) for tensioning
the blade (26) in a clockwise direction.
•
The correct blade tension can be checked
by applying pressure to the side of the blade
with your finger, somewhere in the middle
between the two blade pulleys (7 + 8). You
should only be able to bend the blade (26)
very slightly (approx. 1-2 mm).
•
When the blade is tensioned enough, it will
produce a metallic sound when tapped.
•
Take the tension off the blade when you do
not want to use it for some time; this will help
to prevent overstretching.
•
Caution! The blade may break if the tension
is too high. BEWARE OF INJURY! If the tensi-
on is too low, the powered blade pulley (7) will
spin while the blade does not move.
6.3 Adjusting the blade (fi g. 1-2)
•
CAUTION! The blade tension has to be set
correctly before you can adjust the blade.
•
Undo the fasteners (13) and open the side
cover (12).
Anl_TC_SB_200_1_SPK13.indb 21 Anl_TC_SB_200_1_SPK13.indb 21
EN
•
Turn the upper blade pulley (8) slowly in a
clockwise direction. The blade (26) should run
with its teeth at the front edge of the tire on
the blade pulley (8). If not, the tilt angle of the
upper blade pulley (8) must be corrected.
•
If the blade (26) tends to run to the back of
the blade pulley (8), i.e. towards the machine
frame (25), turn the setting screw (22) anti-
clockwise while turning the blade pulley (8) by
hand until the blade (26) runs in the middle.
•
If the blade (26) tends to run to the front edge
of the blade pulley (8), turn the setting screw
(22) in a clockwise direction.
•
After setting the upper blade pulley (8) you
need to check the blade (26) position on the
lower blade pulley (7). The blade (26) should
run in the middle of the blade pulley (7), as
above. If it does not, you will have to adjust
the tilt of the upper blade pulley (8) again.
•
Turn the upper blade pulley several times
until the adjustment to the upper blade pulley
(8) has an effect on the blade position of the
lower blade pulley (7).
•
After any adjustments have been carried out,
the side covers (12) must be closed again
and re-secured with the fasteners (13).
6.4. Setting the blade guide (Fig. 7 - 10)
Whenever you change the blade you must re-set
both the support bearings (30 + 31) and the guide
pins (28 + 29).
•
Undo the fasteners (13) and open the side
cover (12).
6.4.1. Upper support bearing (30)
•
Undo the socket head screw (33).
•
Move the support bearing (30) so that it is no
longer touching the blade (26). There should
be a maximum gap of 0.5 mm.
•
Re-tighten the socket head screw (33).
6.4.2. Adjusting the lower support bearing
(31)
•
Remove the saw table (15) or tilt it 45°.
•
Swing the blade guard (34) away.
•
Adjust in the same way that the upper support
bearing was adjusted. The blade (26) is only
supported by the support bearings (30 + 31)
during cutting. When idle the blade should not
touch the ball bearing.
6.4.3. Adjusting the upper guide pins (28)
•
Slacken the socket head screw (35).
•
Move the mount (36) of the guide pins (28) so
that there is a gap of approx. 1 mm between
- 21 -
20.05.2025 09:06:29 20.05.2025 09:06:29