Dorman 926-959 Mode D'emploi

INSTRUCTIONS
OIL FILTER
HOUSING KIT
926-959
Patent Information:
dormanproducts.com/patents
BEFORE YOU BEGIN:
• Always wear proper safety
equipment when performing repairs.
• Ensure at your point of purchase
that this part fits your exact
vehicle configuration.
• Reference the appropriate service
manual for your vehicle. If you do
not have a service manual, and do
not have the training or experience
to perform the necessary
procedures correctly, seek the
services of a qualified technician.
NEED HELP?
Please call our Technical Support
team for assistance from our team of
certified automotive experts.
1-866-933-2911
© 2025 No reproduction in whole or in part without prior written approval.
926-959_Instructions_v6
This kit replaces the original plastic oil filter housing with
a robust aluminum design.
This oil filter housing is of the later model year design
and will require a 2014 model application oil filter for
future oil changes applicable. See oil filter reference
chart below.
Oil Filter
Hastings
Denso
Wix
Fram
Purolator
Mobil 1
INSTRUCTIONS
STEP 1:
Remove the oil filter cap and filter before removing old
housing. Remove oil filter housing and cooler assembly
from engine per vehicle service manual. Clean mating
surface after removal.
STEP 2:
Remove sensor(s) from original housing.
STEP 3:
Install cooler-to-housing gaskets into gasket grooves in
oil filter housing.
STEP 4:
Install oil cooler onto new housing. Using oil cooler
screws, fasten cooler to housing. Tighten cooler-to-
housing screws to 9 lbs-ft (12 N-m).
STEP 5:
Coat sensor threads with thread sealant and install water
and oil (if equipped) sensor(s) into oil filter housing.
Tighten sensor(s) to 15 lbs-ft (20 N-m).
NOTE: Certain model housings will be equipped
with an oil temperature sensor. If your original
housing does not have a temperature sensor,
install plug into unused opening and tighten
to 25 lbs-ft (34 N-m).
Dorman Products, Inc. Corporate Office and Customer Service: 1-800-523-2492.
Disclaimer: It is impossible in these instructions to account for all possible circumstances or situations that you may experience when at-
tempting to install this product. Please consult with a qualified auto technician before attempting to perform any work you are not qualified to
do. Automobiles can be hazardous to work on; be sure to take all necessary safety precautions. Failure to do so may result in property damage
or personal injury. Certain motor vehicle standards and performance requirements may apply to your motor vehicle (such as Federal Motor
Vehicle Safety Standards by the National Highway Traffic Safety Administration). Be sure that your work is performed in accordance with such
standards and that you do not disable any motor vehicle safety feature.
STEP 6:
Model year
Black O-ring
Part No.
LF697
1503066
WL10010
CH11665
L36296
M1C456A
Install new O-ring onto front oil return port on housing.
Lubricate with light coat of oil for ease of installation. The
O-ring indicated by the arrow will differ depending
on the model year of the vehicle. Refer to diagram
above to determine which O-ring to use in this location
for your vehicle.
STEP 7:
Install remaining seals.
NOTE: Either the 22.3mm black O-ring
or the 23mm blue O-ring will be left over
in every installation.
STEP 8:
1
Install oil filter housing. Ensure front oil return port is
fully seated into engine block before tightening mounting
bolts. Tighten oil filter housing bolts in the sequence
shown to 9 lbs-ft (12 N-m). If installing in a 2013 or earlier
vehicle, place decal with information about the new filter
in a conspicous location in engine bay.
STEP 9:
Install largest included O-ring onto oil filter cap. Install
new oil filter onto oil cap. Lubricate O-ring on cap and
small O-ring on the tip of the oil filter with a light coat of
oil. Tighten cap to at least 18 lbs-ft (25 N-m) but no more
than 22 lbs-ft (30 N-m).
STEP 10:
Check oil level and add oil to crankcase to compensate
for lost oil from replacing oil filter.
STEP 11:
Check coolant level and top off coolant level to
compensate for lost coolant during installation. Bleed
the coolant system.
STEP 12:
Test drive vehicle to ensure there are no coolant
or oil leaks.
PAGE 1 OF 3
Model year
2011-2021 2022+
Blue O-ring
22.3mm
23mm
5
3
4
2