Dorman 927-932 Manuel D'instructions

INSTRUCTIONS
CATALYTIC
CONVERTER
THEFT
DETERRENT
SHIELD
927-932
BEFORE YOU BEGIN:
• Always wear proper safety
equipment when performing repairs.
• Ensure at your point of purchase
that this part fits your exact
vehicle configuration.
• Reference the appropriate service
manual for your vehicle. If you do
not have a service manual, and do
not have the training or experience
to perform the necessary
procedures correctly, seek the
services of a qualified technician.
NEED HELP?
Please call our Technical Support
team for assistance from our team of
certified automotive experts.
1-866-933-2911
© 2024 No reproduction in whole or in part without prior written approval.
927-932_Instructions
KIT CONTENTS
• Shield
• Rivet nuts (Qty: 10)
• 20mm security star bolts (Qty: 4)
• 50mm security star bolts (Qty: 2)
• 65mm security star bolts (Qty: 2)
• Washers (Qty: 10)
INSTRUCTIONS
STEP 1:
Stud
Remove splash shield. Use mounting studs
to locate the anti-theft device. Using the device
as a template, mark mounting hole locations
to vehicle. Drill 3/8" holes at each location.
Existing splash shield mounting nuts may
be used to mount both OEM splash shield
and anti-theft device.
STEP 2:
Rivet tool
Install rivet nuts into holes using included tool.
Thread the large bolt completely into the acorn
nut. Slide the smaller bolt inside the large bolt
and nut, and capture it using the rivet nut with
the flanged portion seating against the acorn
nut. Insert the rivet nut into the drilled hole.
Using a wrench, hold the acorn nut. Making sure
the rivet nut flange is flush to the vehicle body,
loosen the large diameter bolt using a wrench or
socket. You will feel resistance as the tool seats
the rivet nut. Continue loosening the bolt until it
stops. The rivet nut is now seated. To remove tool,
continue holding the acorn nut and tighten the
large diameter bolt 90°. The small bolt may be
loosened, and the entire tool will be free to reset
and reuse.
Dorman Products, Inc. Corporate Office and Customer Service: 1-800-523-2492.
Disclaimer: It is impossible in these instructions to account for all possible circumstances or situations that you may experience when at-
tempting to install this product. Please consult with a qualified auto technician before attempting to perform any work you are not qualified to
do. Automobiles can be hazardous to work on; be sure to take all necessary safety precautions. Failure to do so may result in property damage
or personal injury. Certain motor vehicle standards and performance requirements may apply to your motor vehicle (such as Federal Motor
Vehicle Safety Standards by the National Highway Traffic Safety Administration). Be sure that your work is performed in accordance with such
standards and that you do not disable any motor vehicle safety feature.
• Long spacers (Qty: 2)
• Short spacers (Qty: 2)
• Nuts (Qty: 3)
• Rivet tool
• Security star tool
Not all hardware will be used during installation,
depending on usability of existing studs.
STEP 3:
Stud
Stud Stud (if
usable)
Rivet nut
65mm
security
star bolts
and long
spacers
Secure front of shield to existing studs (if usable)
with three included nuts. Install four 20mm
security star bolts and washers into rivet nuts
at front of shield. Install security star bolts,
washers and spacers to four mounting points at
rear of shield. The two 50mm security star bolts
and short spacers install at the two rearmost
mounting points of the shield. The two 65mm
security star bolts and long spacers install in the
other two rear shield mounting points. Only hand-
tighten hardware at this point.
STEP 4:
Tighten all security star bolts using included
security star tool.
PAGE 1 OF 3
20mm security
star bolts
50mm security star
bolts and short spacers