Publicité
English
Automatic defrosting
Ice may form in the cooling cham-
ber if the appliance is used for a
long time and depending on the
humidity of the air. To maintain a
consistent cooling performance,
the BEEZER
defrosts automat-
®
ically. This happens by default
after 90 minutes.
The automatic defrosting process
lasts approx. 5 minutes. During
the defrosting process, the LED
ring on the BEEZER
®
cyan, while the display uses bars
to indicate how the process is
progressing.
When automatic defrosting has
been successfully completed, the
appliance switches to pre-cooling
mode and is ready for operation
after a further 5 minutes.
Note:
The pre-settings for automatic
defrosting can be adjusted in the
app.
Switching off
• Press and hold down the start
button (5.1) to switch the appli-
ance off. The defrosting process
then begins automatically and
lasts approx. 10 minutes.
• During the defrosting process,
the LED ring on the BEEZER
lights up yellow, while the display
uses bars to indicate how the
process is progressing.
• Once defrosting has been
completed after the appliance
is switched off, the door must
be opened to allow moisture to
escape. This is indicated by the
device producing an acoustic
signal (beeping). Ideally, the door
should remain open for at least
60 minutes.
• When the cooling chamber
door is closed, the appliance
is switched off and ready to be
switched back on again.
18
Note:
If the appliance is to remain
unused for an extended period,
you should first ensure that the
cooling chamber is completely
clean and dry and that the cool-
ing chamber door is left open to
prevent mould from forming in the
interior (see CLEANING).
ENERGYSAVING MODE
If the appliance is ready for
lights up
operation and has still not been
used after a period of 10 min-
utes, the BEEZER
energy-saving mode. When the
appliance is in energy- saving
mode, the LED ring of the
BEEZER
If the appliance is in energy-
saving mode, it can be re-
activated by pressing any
function key. If the temperature in
the cooling chamber is too high,
another short pre-cooling process
is started (see the instructions for
pre-cooling the appliance). This
process should last less than
1 minute, after which the appli-
ance will be ready for operation.
If it is not re-activated, the appli-
ance automatically switches off
completely after 60 minutes as
standard.
®
Note:
The pre-settings for energy-
saving mode and automatic
switch-off can be adjusted in
the app.
CLEANING
The BEEZER
cleaning after each use. How-
ever, the cooling chamber of the
BEEZER
needed.
switches to
®
lights up purple.
®
does not require
®
can be cleaned as
®
Preparation
• Open the cooling chamber
door (1). Carefully remove any
foreign matter!
• Remove the rotating rail (11)
from the cooling chamber (13).
The underside of the rail is mag-
netically attached and must be
kept in a horizontal position when
being pulled upwards to avoid it
becoming jammed.
• Then pull out the strainer
tray (12) located below the
rotating rail.
Regular cleaning
• Rinse the rotating rail (11) and
the strainer tray (12) under clear
water.
• Wipe the cooling chamber of
the BEEZER
with a damp cloth.
®
Cleaning of heavy soiling in the
cooling chamber
If the cooling chamber is heavily
soiled (leaked liquid, fragments
of glass or other foreign matter,
e.g. due to the beverage con-
tainer being damaged or not
being tightly sealed), follow the
steps below:
• Rinse the rotating rail (11) and
the strainer tray (12) under clear
water. Take care when removing
foreign matter such as glass
fragments or similar!
• Feed the drain hose (8) located
on the rear of the BEEZER
a sufficiently large container or
basin with a drainage outlet.
• Then clean the cooling cham-
ber by rinsing it with plenty of
water. Do not use a high-pressure
cleaner!
Note:
The BEEZER
must not be tipped
®
over!
Note:
After each cleaning, leave the
cooling chamber door open
(ideally for at least 60 minutes) to
allow moisture to escape.
into
®
Publicité
