Publicité
English
If the door is not closed again,
the appliance draws attention to
this by emitting an acoustic signal
(beeping). If the door is left open,
this raises the temperature in the
cooling chamber, which in turn
results in the cooling process
being repeated or taking longer
to complete.
Once defrosting has been
completed after the appliance
is switched off, the door must
be opened to allow moisture to
escape. This is indicated by the
device producing an acoustic
signal (beeping). Ideally, the door
should remain open for at least
60 minutes.
Drain hose
The liquid produced during
the defrosting process, by an
unsealed bottle or due to a
broken bottle can be drained
manually using the drain hose (8)
located on the rear of the
BEEZER
.
®
To do this, take the drain hose (8)
out of its holder and feed it into
a sufficiently large container or
basin with a drainage outlet with
the opening pointing downwards.
Note:
The volume of water produced by
the defrosting process depends
to a large extent on ambient air
humidity. Water only needs to be
drained via the hose if a large
volume is produced due to very
high air humidity.
The BEEZER
also has an
®
overflow vent (10) on the rear of
the appliance. If excess water
accumulates in the interior of
the appliance, e.g due to an
excessive volume of condensate
or a bottle breakage, it can drain
through this vent. This presents
no problems for the BEEZER
itself, but should be considered
when choosing the surface on
which the appliance is positioned.
16
BEFORE USING THE
APPLIANCE FOR THE
FIRST TIME
Preparation
• Carefully take the appliance
out of the packaging and remove
all packaging parts and protective
film.
• Keep all packaging parts
together with the packaging in a
safe place. When disposing of
the packaging parts later, please
observe the statutory regulations
governing proper disposal.
CAUTION, risk of explosion:
Do not use the appliance if the
system has been damaged! If
this happens, the room must
be well ventilated at all times
and any potential ignition
sources removed.
Positioning the appliance
• Place the BEEZER
non-slip, water-resistant surface
close to a mains socket. You
should only ever lift the BEEZER
using the handles provided on
the front and rear (6).
Note: Never lift the BEEZER
using the door or other parts
of the appliance other than the
handles provided.
• Note that the BEEZER
only be used in well ventilated
spaces where no potential
ignition sources are present. Also
take care to keep the air vents (7)
uncovered. For this purpose,
ensure that a sufficient distance
of approx. 5 cm is kept between
the appliance and the sur-
rounding walls (see GENERAL
SAFETY INSTRUCTIONS).
• Plug the power cord into the
socket.
®
Note:
The BEEZER
ported, stored and operated in an
upright position. Before using the
appliance for the first time, leave
it to stand in the same location for
on a flat,
®
®
®
must
®
must be trans-
®
at least 12 hours. The appliance
is intended to be used at a room
temperature of 16 C to 32°C.
BEEZER
Connect
®
The BEEZER
can be controlled
®
using the app. To download and
install BEEZER
Connect on your
®
smartphone or tablet, scan the
QR code on the front of these
operating instructions. Alterna-
tively, you can also search for
BEEZER
Connect in the App
®
Store or Google Play Store.
Note:
The app serves as an extension
of the LED and appliance display.
You can check additional infor-
mation in the app, such as the
current temperature of the cooling
chamber.
Connecting the BEEZER
WiFi
• Connect the BEEZER
WiFi network by pressing the two
lower function buttons (5.3 and
5.4) at the same time. A success-
ful connection is indicated by the
WiFi symbol on the display (see
FUNCTIONS).
Connect BEEZER
to
®
BEEZER
Connect
®
• Open BEEZER
Connect on
®
your smartphone or tablet.
• Choose the "Register" function
and create a personal customer
account. To do so, you need
to enter a phone number or
e-mail address (these details are
required to access all functions of
the app).
• Connect your smartphone or
tablet to your home WiFi network.
• Activate Bluetooth
®
smartphone or tablet.
• Open BEEZER
Connect, log
®
in to your account and select
"Add device (+)" on the home
page.
to
®
to your
®
on your
Publicité
