Dea NET24N Notice D'emploi Et Avertissements page 44

NET24N
P062 Electric lock output activation
If=0 "boost" output for electric-lock art.110 power supply, If=1 24V output controlled
by the ELOCK_IN input as pulsed mode,If=2 24V output controlled by the ELOCK_IN
input as step-by-step mode, If=3 electro-brake output for not self-locking operators,
If=4 24V output for electric-lock power supply via an external relay, If=5 24V output for
electro-magnets power supply for barriers, If>5 24V output controlled by the ELOCK_
IN input as temporized mode (the set value indicates the switch-off delay in seconds).
Warning: To adjust the activation/deactivation times in the 000 | 004 | 005 modes,
use parameter P064.
P063 Motor running direction
If=1 automatically reverses the outputs open/close of the operators, avoiding having
to manual change the wiring when installing the operator in an inverted position.
Warning: Changing this parameter you need to change the parameters for the opening
and closing limit switches.
P064 Electric lock duration adjustment
If P062=000 | 004, adjust the activation time of the LOCK output;
If P062=005, adjust the deactivation time of the LOCK output;
P065 Maintenance manoeuvre counter
If = 0 reset the counter and disables the intervention request , if> 0 indicates the
number of operations (x 500) to be made before the control panel executes a 4
second additional pre-flash to indicate the need of maintenance.
i.g.: If P065 = 050, operations number = 50x500 = 25000 operations
Warning: Before you set a new value of the counter-manoeuvres maintenance, the
same must be reset by setting P065= 0 and only later P065 = "new value".
P066 Selection of operating flashing light output
If=0 intermittent flashing light output; If=1 Fixed flashing light output (for flashing
lights with intermittent interior circuits).
P067 SAFETY_1
If = 0 safety edge always enabled, if = 1 safety edge enabled only while closing, if = 2
safety edge enabled only while closing and before any movement, if = 3 safety edge
enabled only when opening, if = 4 safety edge enabled only while opening and before
any movement; as for the obstacle detection with internal anti-crushing sensor, also
the activation of the inputs SAFETY_1 and SAFETY_2 causes the complete or partial
reversal as set by P055 (duration of inversion on obstacles while opening, and P056
(duration of reversal on obstacle while closing)
P068 SAFETY_2
If = 0 safety edge always enabled, if = 1 safety edge enabled only while closing, if = 2
safety edge enabled only while closing and before any movement, if = 3 safety edge
enabled only when opening, if = 4 safety edge enabled only while opening and before
any movement; as for the obstacle detection with internal anti-crushing sensor, also
the activation of the inputs SAFETY_1 and SAFETY_2 causes the complete or partial
reversal as set by P055 (duration of inversion on obstacles while opening, and P056
(duration of reversal on obstacle while closing)
P069 Delay on limit switch detection
The operation is stopped after 1,5 sec from limit switch detection. When during this
delay a stop is detected, the operator is suddenly stopped
P070 Adjustment of acceleration durability
Warning: if soft start is activated, the acceleration is deactivated indipendently from
P070 value.
42
000 000 000
• 000: "Boost" output for electric-lock
art.110 power supply
• 001: "24V pulse output max 5W
• 002: "24V step-by-step output
max 5W
• 003: "Electro-brake output for not
self-locking operators
• 004: "Output for electric-lock power
supply via an external relay
• 005: "output for electro-magnets
power supply for barriers
• >005: "24V temporized output
max 5W (6sec..................255sec)
000 000 000
• 000: "Standard installation"
• 001: "Inverted installation"
002 002 002
0s..................10s
000 000 000
• 000: "Request Maintenance disabled
• >000: "Number of operations (x 500)
for required maintenance
(1...................................255)
001 001 001
• 000: "intermittent flashing light output
• 001: "fixed flashing light output
000 000 000
• 000: "safety edge always enabled
• 001: "safety edge enabled only while
closing
• 002: "safety edge enabled only while
closing and before any movement
• 003: "safety edge enabled only when
opening
• 004: "safety edge enabled only while
opening and before any movement
000 000 000
• 000: "safety edge always enabled
• 001: "safety edge enabled only while
closing
• 002: "safety edge enabled only while
closing and before any movement
• 003: "safety edge enabled only when
opening
• 004: "safety edge enabled only while
opening and before any movement
000 000 000
• 000: "limit switch delay disabled
• 001: "limit switch delay enabled
200 200 200
• 000: "acceleration deactivated (it runs
an acceleration of minimum durability,
almost imperceptible)
• 00X: "adjusts the acceleration
durability at 1,5 sec (X*6 ms)
005
000
002
000
001
000
000
000
200