Dea NET24N Notice D'emploi Et Avertissements page 43

P055 Reversal due to obstacle during opening
Adjust the inversion on obstacle period (detected by internal anti-crushing sensor
or by the safety input when activated): If = 0 it makes a complete inversion, if> 0
indicates the duration (in seconds) of the run, after inversion resulting from detection
of an obstacle during the opening.
P056 Reversal due to obstacle during closing
Adjust the inversion on obstacle period (detected by internal anti-crushing sensor
or by the safety input when activated): If = 0 it makes a complete inversion, if> 0
indicates the duration (in seconds) of the run, after inversion resulting from detection
of an obstacle during the closing.
P057 Manual unlocking facilitation with gate closed
If≠0, after ending the closing or opening maneuver, the engine reverses for a brief
time to release the pressure on it, and thus facilitate the manual release. The set
value shows the length of the inversion. If=0 function disabled
P058 Adjustment of the opening stroke margin
It adjusts the duration of the last part of the stroke during which an obstacle is
interpreted as a stroke, blocking the motor without performing the inversion.
For motors with encoders, the set value indicates the number of revolutions of the
rotor; while for motors without encoder, the value is expressed in% of the maximum
stroke.
Warning: for motors without encoder, if P035 (duration slow-down while opening) is
>10%, it forces the stroke detection margin so that it's the same than the slow-down.
TYPE 02 ONLY: Duration adjustment for the secondary force in closing: adjusts the
duration of the last part of the closing movement, in which the force is managed sepa-
rately with P039. The value is expressed in number of revolutions of the rotor.
P059 Adjustment of the closing stroke margin
It adjusts the duration of the last part of the stroke during which an obstacle is
interpreted as a stroke, blocking the motor without performing the inversion.
For motors with encoders, the set value indicates the number of revolutions of the
rotor; while for motors without encoder, the value is expressed in% of the maximum
stroke.
Warning: for motors without encoder, if P036 (duration slow-down while closing) is
>10%, it forces the stroke detection margin so that it's the same than the slow-down.
TYPE 02 ONLY: Adjustment of the stop-margin in closing: adjusts the duration of the
last part of the closing movement, in which an obstacle is seen as a stop, causing the
motor to stop without reversal on the obstacle. The value is expressed in number of
revolutions of the rotor.
P060 Operators force adjustment at stroke arrival
Operators force adjustment at stroke arrival - If=0, setting off (the force value on the
stroke is calculated automatically) - If≠0 (operators with encoder) it indicates the force
value (expressed in% of the max value) set in the last length.
TYPE 02 ONLY: Force adjustment in the stop margin in closing, its duration is set
through P059.
P061 "ENERGY SAVING" function
If=1 after 10sec of inactivity, the control panel turns the 24V outputs and the display
off that will be turned on at first command received (use recommended battery-
powered and / or solar panel).
Warning: when "Energy saving" is enabled, SAS function is not available.
Warning: when "Energy saving" is enabled, only the stabilized output 24V_ST must be
used to power accessories.
003 003 003
• 000: complete reversal on obstacle
• >000: duration of reversal on obstacle
(1sec.................10sec)
003 003 003
• 000: complete reversal on obstacle
• >000: duration of reversal on obstacle
(1sec.................10sec)
000 001 003
• 000: facilitazione sblocco disattivata
• >000: facilitazione sblocco attivata
con durata pari a:
(1x25ms..................20x25ms)
(1x25ms..................40x25ms) (TYPE 00
only)
012 025 000
1..................255 (motors with encoder)
1%...............100% (motors
encoder)
0..................255
012 025 025
1..................255 (motors with encoder)
1%...............100% (motors
encoder)
1..................255
000 035 000
0%..................100%
000 000 000
• 000: "Energy saving" not active
• 001: "Energy saving" active
NET24N
000
000
002
020
without
020
without
000
000
41