Baustufe 7, Bestücken der Bäume, Teile 7.1 - 7.16
Nr.
Bezeichnung, Maße in mm
7.1
S - Haken, ø 1,4 x 12
7.2
Wirbellager
7.3
Gummiring
7.4
Schraube, M 2 x 40
7.5
S - Haken, ø 1,4 x 12
7.6
Bundbuchse, ø 2,2 x ø 3,6 x 6
7.7
Nockbeschlag
7.8
Trimmgewicht, ca. 40 g
7.9
Achse, ø 3,5 x 150
7.10
S - Haken, ø 1,4 x 12
7.11
Stellring, ø4 x ø 7 x 5
7.12
Madenschraube, M 3 x 3
7.13
Fockstag, ø 1
7.14
Schrumpfschlauch, ø2,4 x 15
7.15
Hülse, ø1,7 x ø 2,5 x 5
7.16
Großbaumlager, 1 x 6 x 33
Fockbaum
- 2 S - Haken 7.1 aufbiegen, im Wirbellager 7.2 einhängen und ver-
schließen.
- Wirbellager und hinteren S - Haken 7.1 durch Einschieben des
Arretierungsdrahtes 6.4 im Fockbaum beweglich fixieren.
- Gummiring 7.3 doppelt legen und auf den Fockbaum ziehen.
- Den Nockbeschlag (mit S - Haken) aus den Teilen 7.4 - 7.7 zusam-
mensetzen.
- Ende des Fockbaums leicht zusammendrücken und die Einheit
7.4 - 7.7 einsetzen. Die Bundbuchse muß stramm sitzen.
- Das
Trimmgewicht
7.8
mit
der
Achse
Trimmgewicht wiederum lackieren.
- Die Achse in den Fockbaum schieben, dabei S - Haken 7.10 und
Stellring 7.11 mit Madenschraube 7.12 mit einsetzen.
- Die Madenschraube 7.12 zur Sicherung anziehen.
- Das Fockstag 7.13 ablängen (15 cm länger als die Vorderkante
des Focksegels).
Hinweis: Bilden von Augen (Dieser Vorgang wiederholt sich an ande-
ren Stellen).
- Zum Bilden eines Auges an einer Litze werden ein Stück
Schrumpfschlauch 7.14 und eine Hülse 7.15 aufgeschoben.
- Das Ende durch den vorderen S - Haken des Fockbaums führen
und in die Hülse fädeln.
- Hülse zusammenpressen, Schrumpfschlauch über das Ende
schieben, um Verletzungen zu vermeiden.
Großbaum
- 1 S - Haken 7.1 mit dem Arretierungsdraht 6.5 festsetzen.
- Den doppelt gelegten Gummiring 7.3 aufziehen.
- Nockbeschlag aus den Teilen7.4, 7.6 und 7.7 zusammensetzen
und einbauen.
- Das Großbaumlager 7.16 einkleben - Überstand beachten.
Bauanleitung, Assembly instructions, Notice de montage
Stage 7, fitting out the booms, parts 7.1 - 7.16
Stück
No.
Description, size in mm
4
7.1
S-hook, 1.4 Ø x 12
1
7.2
Swivel
2
7.3
Rubber band
2
7.4
Screw, M2 x 40
1
7.5
S-hook, 1.4 Ø x 12
2
7.6
Flanged bush, 2.2 Ø x 3.6 Ø x 6
2
7.7
Peak fitting
1
Blei
7.8
Trim weight, approx. 40 g
1
7.9
Shaft, 3.5 Ø x 150
2
7.10
S-hook, 1.4 Ø x 12
1
7.11
Collet, 4 Ø x 7 Ø x 5
1
7.12
Grubscrew, M3 x 3
1
Litze
7.13
Forestay, 1 Ø
1
n.e.
1
7.14
Heat-shrink sleeving, 2.4 Ø x 15
1
7.15
Sleeve, 1.7 Ø x 2.5 Ø x 5
7.16
Main boom support, 1 x 6 x 33
Jib boom
- Open up two S-hooks 7.1, connect the swivels 7.2 and close them
again.
- Slip the retaining wire 6.4 through the jib boom and attach the swi-
vels and the rear S-hook 7.1. These parts must be free to move.
- Double up the rubber band 7.3 and push it onto the jib boom.
- Assemble the peak fitting (with S-hook) from parts 7.4 - 7.7.
- Gently squeeze the end of the jib boom and insert the peak fitting
assembly 7.4 - 7.7. The flanged bush must be a tight fit.
7.9
verkleben.
- Glue the trim weight 7.8 to the shaft 7.9. Paint the trim weight.
- Push the shaft into the jib boom, fitting the S-hook 7.10 and the
collet 7.11 (with grubscrew 7.12) at the same time.
- Tighten the grubscrew 7.12 to secure these parts.
- Cut the forestay 7.13 to length (15 cm longer than the front edge
of the jib).
Note: forming loops (this procedure is required repeatedly from this
point on):
- To form a loop in a piece of braided wire first slip a piece of heat-
shrink sleeving 7.14 and a crimp sleeve 7.15 onto the wire.
- Pass the end of the wire through the front S-hook in the jib boom
and thread it back into the crimp sleeve.
- Squeeze (crimp) the sleeve and push the heat-shrink sleeve over
the end to avoid injury from the sharp wire.
Main boom
- Secure one S-hook 7.1 with the retaining wire 6.5.
- Pull the doubled-over rubber band 7.3 into position.
- Assemble the peak fitting from parts 7.4, 7.5 and 7.7 and install it.
- Glue the main boom support 7.16 in place, noting the amount by
which it should project.
WINDSTAR
No. off
4
1
2
2
1
2
2
1
Lead
1
2
1
1
1
Braided
wire
1
N.I.
1
1
23
Stade 7, équipement des bômes, pièces 7.1 à 7.16
N°
désignation, cotes en mm
7.1
crochets, Ø 1,4 x 12
7.2
émerillon
7.3
élastique
7.4
vis, M 2 x 40
7.5
crochet, Ø 1,4 x 12
7.6
manchon à épaulement, Ø 2,2 x Ø 3,6 x 6 2
7.7
armature de tête du mât
7.8
contrepoids, approx. 40 g
7.9
axe, Ø 3,5 x 150
7.10
crochet, Ø 1,4 x 12
7.11
bague d'arrêt, Ø 4 x Ø 7 x 5
7.12
vis sans tête, M 3 x 3
7.13
draille de foc, Ø 1
7.14
gaine thermorétractable, Ø 2,4 x 15
7.15
cosse, Ø 1,7 x 2,5 x 5
7.16
vit-de-mulet, 1 x 6 x 33
Bôme de foc
- Ouvrir deux crochets 7.1, les accrocher à l'émerillon 7.2 et les
refermer.
- Fixer l'émerillon et crochet arrière 7.1 à la bôme de foc en instal-
lant le fil d'arrêt 6.4, l'émerillon doit cependant conserver sa mobi-
lité.
- Installer l'élastique 7.3 en double et l'enfiler sur la bôme de foc.
- Assembler l'armature de tête du mât (avec crochet) à partir des
éléments 7.4 à 7.7.
- Écraser légèrement l'extrémité de la bôme de foc et mettre l'unité
7.4 à 7.7 en place. Le manchon à épaulement doit être bien tendu.
- Coller le contrepoids 7.8 à l'axe 7.9. Le peindre également.
- Glisser l'axe dans la bôme de foc en mettant simultanément le
crochet 7.10 et la bague d'arrêt 7.11 avec vis sans tête 7.12 en
place.
- Serrer la vis sans tête 7.12 pour bloquer l'ensemble.
- Couper la draille de foc 7.13 à la longueur indiquée (15 cm de plus
que l'arête avant du foc).
À noter: former un œillet (cette procédure est reprise plusieurs fois
ultérieurement).
- Pour former un œillet sur un filin, y enfiler un morceau de gaine
thermorétractable 7.14 et une cosse 7.15.
- Passer l'extrémité par le crochet avant de la bôme de foc et enfi-
ler la cosse.
- Écraser la cosse, glisser la gaine thermorétractable sur l'extrémi-
té pour éviter toute blessure.
Bôme de grand voile
- Bloquer le crochet 7.1 avec le fil d'arrêt 6.5.
- Mettre l'élastique double 7.3 en place.
- Assembler la têtière à partir des pièces 7.4, 7.6 et 7.7 et l'installer.
- Coller le vit-de-mulet 7.16 - observer le dépassement indiqué.
No.
1087
nombre
4
1
2
2
1
2
1
plomb
1
2
1
1
1
fil
métallique
1
n.c.
1
1