EINHELL FREELEXO Basic Instructions D'origine page 39

Explanation of the button options on the con-
trol panel (Fig. 9b)
60. Buttons for setting the mowing time and for
entering the PIN
61. "HOME" button
62. Locking button
63. "OK" button
64. "START" button
6.3 Cutting height adjustment facility
Important! Adjust the cutting height only when
the robot lawn mower has been switched off . Do
this by pressing the STOP button (3). The cutting
height adjustment facility (4) allows the cutting
height of the robot lawn mower to be set to infi ni-
tely adjustable settings between 20 and 60 mm,
which can be viewed on the scale.
If the grass is taller than 60 mm it has to be shor-
tened to a maximum of 60 mm fi rst to avoid expo-
sing the robot lawn mower to excessive load and
adversely aff ecting its operating effi ciency. Use a
conventional lawn mower or trimmer to do this.
After installation has been completed, the cutting
height can be adjusted using the cutting height
adjustment facility (4). Always start with a higher
cutting height and reduce it in small steps until
you reach the desired height.
6.4 Locking mechanism / PIN
The locking mechanism prevents the unautho-
rized use of the robot lawn mower without a valid
code. You have to enter a personal four-digit secu-
rity code for this.
Lock release
- Before you start using the robot lawn mower,
you have to enter the correct PIN (standard
PIN: "1-2-3-4"). Open the display cover (25)
and press the locking button (62). Then enter
the PIN slowly in sequence and confi rm the
entry with the "OK" button (63). The control
functions will be unlocked and the lock LED
(51) will light up green.
- If you have entered an incorrect PIN, the lock
LED (51) will light up red. Press the locking
button (62) and re-enter the PIN.
Lock
If you want to lock the control panel (2), press the
locking button (62). The lock LED (51) will light
up red.
Standard PIN: New PIN:
1 2 3 4 _ _ _ _
Anl_FREELEXO_Basic_SPK9.indb 39 Anl_FREELEXO_Basic_SPK9.indb 39
GB
Changing the PIN
To change the PIN, proceed as follows.
1. Unlock the control panel.
2. Press the "OK" button (63) and the "4H"
button (60) simultaneously and hold for 3
seconds. The time LEDs (50) will fl ash simul-
taneously.
3. Enter a new PIN (four digits). Press the "OK"
button (63).
4. Repeat step 3 to confi rm the new PIN.
5. Important! Make a note of your new PIN.
Requesting your PIN if you lose it
Have the receipt and the serial number of the
robot lawn mower ready. You need them in order
to get your PIN.
1. Connect an empty USB stick to the USB con-
nection (26) as shown (Fig. 11).
2. Switch on the main switch (7) (ON).
3. The robot lawn mower will automatically save
the PUK to your USB stick and will then end
the operation with a beep.
4. Pull out the USB stick. Import the data from
the USB stick to a computer. A text fi le (*.txt)
will have been created by the robot lawn
mower. This fi le contains a PUK, a personal
code. Please contact the customer services
team to obtain your PIN.
6.5 Robot lawn mower settings
Setting the mowing time
1. Unlock the control panel (2).
2. Select the desired mowing time by pressing
the corresponding button:
2.1 If you press the corresponding button briefl y,
the robot lawn mower will mow daily. The
corresponding display will appear through
constant lighting of the time LEDs.
2.2 If you press the corresponding button longer,
the robot lawn mower will mow every second
day. The corresponding display will appear
through fl ashing of the time LEDs.
3. The time is shown by the time LEDs (50).
4. To confi rm the setting, press the "OK" button
(63).
The time at which the changes were made is
now the daily starting time. The number of hours
shown is the daily work time.
It is recommended to base the mowing time
setting on 8 hours per day for 500 m² as a guide-
line. The selected working time may need to be
adapted to take account of the garden's size and
complexity.
- 39 -
16.12.2020 13:33:35 16.12.2020 13:33:35