STAMOS Operator Manuel D'utilisation page 9

TECHNICAL SPECIFICATIONS
Product name Welding helmet
Model Operator Sub Blaster Eagle
Zero Eye
Article no. 2980 2981 2982 2983
Optical class
Filter cartridge size 110 mm x 90 mm x 9 mm
Active field of view 95 mm x 36 mm 98 mm x 55 mm
Bright mode 4
Shade mode 4/9-13
Switching time 1/25000 s
Delay time
(dark to light)
Power supply Photoelement Photoelement
+ 2 x CR2450 battery
Working
temperature
Storage
temperature
INSTRUCTIONS
WARNING! Before using the helmet for welding, ensure that you have read and
understood the safety instructions.
• The auto-darkening welding helmets comes ready for use. The only thing you need to do before wel-
ding is to adjust the position of the headband and to select the correct shading factor for your work.
Fig. 1:
16
Firestarter Legend Pokerface Carbonic BlackONE
500
2984 2985 2986 2987 2988
1211 1111
125 mm x 106 mm
100 mm x 65 mm
3
4/4-8/9-13
1/30000 s
0,25-0,8 s
Photoelement
+ CR2450 battery
- 10°C to +55°C
- 20°C to +70°C
Rev. 07.11.2016
WELDING MASK BAND MOUNTING ADJUSTMENT
The entire circumference of the band can be adjusted using the knob at the back of the band (see setting
"3" in figure 1). It is possible to make the adjustment while wearing the mask, by changing the circumfe-
Metalator rence as necessary.If the headband is too high or too low, it can be adjusted as necessary. In order to do
so, loosen the end of the band by removing the clasp from the hole and loosen both ends to increase the
circumference, or pull them together to decrease the circumference; next, snap the clasp using the next
2989
hole (see setting "1" in figure 1) Should it be necessary to adjust the distance between the operator's face
and the filter cartridge, pull back the clamp of holder "2" and set appropriate distance for both sides of
the mask.Check if the mask fits while wearing it, by lifting and lowering the mask several times. If the band
moves when the mask is raised or lowered, it should be readjusted until the band is settled properly.
* The angle of inclination is adjusted by setting the latches "4" – unlock the latch by pulling it back (until
the latch leaves the hole), then move it by the necessary angle and lock the latch. The adjustment is to be
carried out for both sides of the mask.
PARAMETER ADJUSTMENT
A. SELECTION OF SHADING DEGREE
Choose the appropriate degree of light protection, as required by the welding process. Before adjus
ting, refer to table „shading degree table". Use the knob located on the mask to select the appropria
te light protection level.
B. DELAY TIME SELECTION
After finishing welding, the colour of the glass will change automatically from dark to bright, after the
preset delay time, in order to level the afterglow. The delay time/return time can be set using the
„Delay" switch: „Short" (short delay ~0,3-0,5 s) / „Med." (medium delay ~0,4-0,6- s)
/ „Long" (long delay ~0,6-0,9 s).
C. PHOTOSENSITIVITY SELECTION
Photosensitivity can be set smoothly using the knob, between level "Hi (high) or "Lo" (low). The „Hi"
setting is standard, intended for everyday use. If the mask is exposed to excessive light or another
welding machine located nearby, the photosensitivity should be reduced.
D. "GRIND" OPTION SELECTION
If the switch is set to „GRIND", protection from light is disabled. This allows the user to carefully
examine and process the welding place – the mask protects the head. Before resuming welding, make
sure the light protection functions have been enabled again.
Rev. 07.11.2016 17