Working Advice; Maintenance And Service; Maintenance And Cleaning - Bosch Professional GHO 10-82 Notice Originale

OBJ_BUCH-447-003.book Page 11 Monday, October 23, 2017 12:19 PM
Switching On and Off
To save energy, only switch the power tool on when using it.
To start the machine, press the On/Off switch 5 and keep it
pressed.
To lock the pressed On/Off switch 5, press the lock-on button
4.
To switch off the machine, release the On/Off switch 5 or
when it is locked with the lock-on button 4, briefly press the
On/Off switch 5 and then release it.
0 601 594 037:
To start the machine, first push the lock-off button for the
On/Off switch 4 and then press the On/Off switch 5 and keep
it pressed.
To switch off the machine, release the On/Off switch 5.
Note: For safety reasons, the On/Off switch 5 cannot be
locked; it must remain pressed during the entire operation.

Working Advice

 Before any work on the machine itself, pull the mains
plug.
Planing (see figure N)
Set the required planing depth and place the front part of the
planer base plate 8 against the workpiece.
 Apply the machine to the workpiece only when
switched on. Otherwise there is danger of kickback when
the cutting tool jams in the workpiece.
Switch the machine on and guide the machine with even feed
over the surface to be planed.
To achieve high-grade surfaces, work only with low feed and
apply pressure on the centre of the planer base plate.
When machining hard materials (e.g. hardwood) as well as
when utilising the maximum planer width, set only low planing
depths and reduce planer feed, as required.
Excessive feed reduces the surface quality and can lead to
rapid clogging of the chip ejector.
Only sharp blades achieve good cutting capacity and give the
machine longer life.
The integrated park rest 30 also allows for continued planing
at any given location on the workpiece after an interruption:
– With the park rest folded down, place the machine on the
location of the workpiece where the planing is to be contin-
ued.
– Switch on the machine.
– Apply the supporting pressure onto the front part of the
planer base plate and slowly push the machine forward
(). This tilts the park rest upward () so that the rear
part of the planer base plate faces on the workpiece again.
– Guide the machine over the surface to be planed () with
even feed.
Beveling Edges (see figure O)
The V-grooves in the front planer base plate allow quick and
easy beveling of workpiece edges. Depending on required
bevel width, use the corresponding V-groove. For this, place
the planer with the V-groove onto the edge of the workpiece
and guide it along the edge.
Bosch Power Tools
Groove to be used
none
small
medium
large
Planing with Parallel/Beveling Guide (see figures K – M)
Mount the parallel guide 22 or beveling guide 26 to the ma-
chine using the corresponding fastening bolt 25. Depending
on the application, mount the rebating depth stop 29 with fas-
tening bolt 28 to the machine.
Loosen the locking nut 24 and adjust the requested rebating
width on the scale 23. Tighten the locking nut 24 again.
Adjust the requested rebating depth accordingly with the re-
bating depth stop 29.
Carry out the planing procedure several times until the re-
quested rebating depth is reached. Guide the planer applying
sideward supporting pressure.
Beveling with the Beveling Guide
When beveling rebates and
surfaces, adjust the required
slope angle with the angle ad-
justment 27.

Maintenance and Service

Maintenance and Cleaning

 Before any work on the machine itself, pull the mains
plug.
 For safe and proper working, always keep the machine
and ventilation slots clean.
Ensure easy operation of the park rest 30 and clean it regular-
ly.
When the carbon brushes wear below acceptable service tol-
erances, the machine will automatically cut out. The machine
must be sent to customer service for maintenance (for ad-
dress, see the "After-sales Service and Application Service"
section).
If the replacement of the supply cord is necessary, this has to
be done by Bosch or an authorized Bosch service agent in or-
der to avoid a safety hazard.
Replacing the Drive Belt (see figures P – Q)
Unscrew screw 6 and take off the belt cover 7. Remove the
worn drive belt 31.
Before assembling a new drive belt 31, clean both pulleys 32
and 33.
Place the new drive belt 31 on the small pulley 33 first and
then work the drive belt 31 onto the large pulley 32 by hand
while rotating it.
English | 11
Dimension a
(mm)
0–4
2–6
4–9
6–10
1 609 92A 41E | (23.10.17)