Electrical Connection; Water Connection - grandimpianti WR 8 Instructions Pour L'installation Et Mode D'emploi

www.groupdynamics-laundry.com
sales@groupdynamics.lv
(only for coin versions)(* for steam heated
machines only).
5) Be sure that the instruction booklet is not
left in the package and lost.
The packaging materials (plastic bags,
expanded polystyrene, timber, cardboard,
nails, etc.) represent a safety hazard and
consequently must not be left within the
reach of children. Collect and keep for further
transportation or long-term storage (see
chapter 9).
Before connecting the appliance, check that
the rating plate data correspond to those of
the existing electric network .
The display case must be used exclusively
for the purposes it was expressly designed
for.
5. TIPS ABOUT GETTING THE AP-
PLIANCE STARTED
5.1 POSITIONING REQUIREMENTS
This washing machine demands no position-
ing requirements but a level platform. Align
by the use of a spirit level.
After moving the machine, align it again.
Check that the support nuts are securely
fastened.
5.2 SPACE REQUIRED FOR INSTAL-
LATION, USE AND MAINTENANCE
The washing machine requires the minimum
space indicated:
1)Front face of the machine
2)Drain
3)Control panel
4)Automatic cutoff switch (not supplied)*
5)Holes for fastening to floor (by the supports
supplied)
6)Available connection for equipotential
7)Power supply inlet through protective tube
8)Hot water inlet
9)Cold water inlet
10)Steam inlet for steam heated models only)
11)Air break
12)Dispenser
13)Door
14)Emergency puller
15)Door opening handle
16)Fastening supports
17)Rating plate
* The cut-off switch must be in a position
as to be easily reached by the operator in
the event of an EMERGENCY(maximum
distance 3 m).
5.3 ALLOWABLE ROOM CONDITIONS
FOR PROPER CASE SERVICE (infor-
mation for the user).
- TYPE OF ROOM: CLOSED
- MINIMUM TEMPERATURE: 10 °C
(Caution: When ambient temperature is
below 10°C, the electronic parts may work
irregularly)
-MAXIMUM TEMPERATURE : 40 °C
-RELATIVE HUMIDITY : 75% H.R.
-LIGHTING: 100 LUX (valid for Italy; as
for other national provisions regarding
lighting in working premises, consult the
relevant national codes).
5.4 BUILDING WORK
For correct operation, this washing machine
needs being anchored to the floor by means
of the supports supplied.
Considering the high kinetic energy deve-
loped during spinning, positioning the ma-
chine in storeys other than ground floor is
not recommended, as it could generate un-
necessary noise during spinning.
Choose its position according to the logical
path of the laundry and the existing water
and power installations.
Prepare a floor drain lower than the machine
drain outlet and not farther than the length of
the drain elbow supplied.
The height of the concrete base will depend
on the height of the laundry trolley, which
must get to the door but must not hamper
loading/unloading operations.
Cast the anchoring base; bury the supports
supplied using, a pre-shaped mold if neces-
sary,
Seven days after casting, position the machine
and fasten it by the supplied nuts and washers.
Model Floor dynamic load
Mod. 8 8874N
Mod.11 11548N
Mod.18 18250N
Mod.26 28963N
Mod.33 47566N

5.5 ELECTRICAL CONNECTION

The washing machine must be installed by
professionally qualified personnel, in ac-
cordance with the instructions provided by
the manufacturer and local regulations.
Incorrect installation may cause harm to per-
sons, animals or property. The manufacturer
assumes no responsibility for such damage.
As for reaching the connection terminal
board, see paragraph 7.3.
Make sure power supply voltage corresponds
to that indicated on the rating plate of the
washing machine. Consider also that the
maximum allowable power voltage variation
is ±10%.
IMPORTANT: THE WASHING MA-
CHINE MUST BE PROPERLY EARTH-
ED.
To this purpose, the supplied plug has a
specific contact. Be sure that the socket is
provided with the corresponding earth ter-
minal, which must comply with the regula-
tions in force. The manufacturer assumes no
responsibility for any damage resulting from
nonobservance of this accident prevention
principle.
8
In compliance with the latest accident pre-
vention provisions, the machine is fitted
with an external terminal for equipotential
connection.
Ahead of the washing machine there must be
an omnipolar cut-off switch with contacts
spacing at least 3mm, calibrated according
to the maximum rated input (see rating plate
and table below):
Number
Total power
of poles
Electric Steam 230/
Heating Heating. 3
from 550
3
to 1100W
from 1800
3
to 1850W
from 6000
3
to 10000W
from 10000
3
to 13000W
from 18000
3
to 25000W
Place a 20 mm (outer diameter) cable duct
between the cutoff switch and the machine
electric power inlet. This inlet is fitted with
a clamp, so after inserting the duct it will be
necessary to fasten the bolt from inside the
machine.
Use one of the cable types appearing in the
table below. Make sure it is fire-proof and
properly protected.
When the cable has been inserted, secure the
cable clip from inside the machine.
8Hz
8Hz
Number
Total power input Type of cable
of wires
7Hz
Electric Gas or steam 230/ 400/
230/3 400/3
7Hz
heating heating 3 3
from 550 to H05V
4 5
7Hz
1100W V-F
from 1800 to H05V
4 5
1850W V-F
Until H05V
4 5
7000W V-F
Until A07V
4 5
13000W V-F
Until A07V
4 5
19000W V-F
Until A07V
4 5
25000W V-F
The machine must be powered following the
cyclic direction of the phases: R-S-T (A1-
A2-A3) (L1-L2-L3). Altering such a direct-
ion will cause damage to the appliance. It is
possible to test phase direction manually as
follows:
- Connect the three phases, the neutral and
earth wires.
- Turn the wall cut-off switch on and then
press the spin contactor manually: if spinning
is clockwise, the phases are connected cor-
rectly; if not, exchange two of the incoming
phases.
CAUTION: let the importance of the phase
cyclic direction be known to the customer,
user or person in charge of the laundry, in
order to prevent accidental inversion.

5.6 WATER CONNECTION

The washing machine is fitted with a hot
water inlet (approximately 60°C) and a cold
water inlet, both sizing 3/4''.
Diff. Cur.
Nominal
Interv.
Current
Id
In
400/
230/3 400/3
3
4 6 6 30 ma
4 16 10 30 ma
4 20-30 16 30 ma
4 30-40 20 30 ma
4 50-70 30-40 30 ma
Section of each Pipe Cable hol.
wire mm2 diam. size
230/3 400/3 mm Pg
H05V
1 1 16 16
V-F
H05V
2,5 1,5 16 16
V-F
A07V
2,5 1,5 16 16
V-F
A07V
6 2,5 20 21
V-F
A07V
10 6 20 21
V-F
A07V
16 10 25 29
V-F