EINHELL GE-CM 18/33 Li BL Mode D'emploi page 16

equipment in balance.
•
Ensure that all mounting components (i.e.
screws, bolts, nuts, etc.) are always tightened
so that the equipment can be safely operated
at all times.
•
Frequently check the grass catch assembly
for signs of wear.
•
Replace excessively worn or damaged parts
immediately.
•
In order to ensure that you enjoy the
equipment for many years to come, all
screwed parts, as well as the wheels and
axles, should be cleaned and lubricated.
•
Keeping your lawn mower in good condition
not only ensures a long lifespan and high
performance, but also enables the equipment
to thoroughly cut your grass with minimal
effort.
•
The blade is subjected to more wear and
tear than any other component. Therefore,
routinely check the condition of the blade
and make sure that it is tightly fastened. If
the blade is completely worn out, it must be
immediately replaced or ground sharp again.
An excessively vibrating mower means that
the blade is not properly balanced or has
become deformed from striking an object.
In this case, the blade must be repaired or
replaced.
•
There are no other parts inside the equipment
which require maintenance.
7.3 Replacing the blade
For safety reasons, we recommend having the
blade replaced by an authorized professional.
Important! Wear work gloves! Only replace the
blade with a genuine Einhell replacement blade,
as this will ensure top performance and safety
under all conditions.
Carry out the following steps to change the
blade:
1. Undo the fastening screw (Fig. 12).
2. Remove the blade and replace with a new
one.
3. When fi tting the blade, make sure it is
installed in the right direction. The blade
air vanes must project into the motor
compartment (Fig. 12). The dome mounts
must be aligned with the punch holes in the
blade.
4. Then retighten the fastening screw with a
universal wrench (Fig. 12). The tightening
torque should be approx. 18.4 ft./lbs (25 Nm).
Anl_GE_CM_18_33_Li_BL_SPK7_NA.indb 16 Anl_GE_CM_18_33_Li_BL_SPK7_NA.indb 16
EN
At the end of the season, perform a general
inspection of the lawn mower and remove any
grass and dirt which may have accumulated.
At the start of each season, ensure that you
check the condition of the blade. If repairs are
necessary, please contact our customer service
center. Use only genuine spare parts.
Spare blade art. no.: 3405458
8. Disposal and recycling
The equipment is supplied in packaging to
prevent it from being damaged in transit. The
raw materials in this packaging can be reused or
recycled. The equipment and its accessories are
made of various types of material, such as metal
and plastic. Never place defective equipment in
your household refuse. The equipment should
be taken to a suitable collection center for proper
disposal. If you do not know the whereabouts of
such a collection point, you should ask in your
local council offi ces.
9. Storage and transport
Remove the rechargeable battery.
Store the equipment and its accessories out
of children's reach in a dark and dry place at
above freezing temperature. The ideal storage
temperature is between 50°F and 104°F (10°C
and 40°C). Keep the electric tool in its original
packaging.
Transport
•
Switch the machine off and isolate it from the
power supply before transporting it.
•
Fit the shipping protectors, if any.
•
Protect the machine from damage and the
strong vibrations that can occur particularly
when transporting in vehicles.
•
Secure the machine against slipping and
tipping over.
The reprinting or reproduction by any other
means, in whole or in part, of documentation
and papers accompanying the products is
strictly subject to the express consent of Einhell
Germany AG.
Subject to technical changes.
- 16 -
15.11.2023 09:25:41 15.11.2023 09:25:41