EINHELL GE-CM 18/33 Li BL Mode D'emploi page 13

Reduce noise generation and vibration to a
minimum!
•
Use only equipment that is in perfect
condition.
•
Maintain and clean the equipment regularly.
•
Adapt your way of working to the equipment.
•
Do not overload the equipment.
•
Have the equipment checked if necessary.
•
Switch off the equipment when not in use.
•
Wear gloves.
CAUTION!
Residual risks
Even if you use this electric power tool in
accordance with the instructions, certain
residual risks cannot be eliminated. The
following hazards may arise in connection
with the equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear
protection is applied.
Warning!
This equipment generates an
electromagnetic fi eld during operation. Under
certain circumstances this fi eld may actively
or passively impede medical implants. To
reduce the risk of serious or fatal injuries, we
recommend persons with medical implants
to consult their doctor and the manufacturer
of the medical implant prior to using the
equipment.
5. Before starting the equipment
The lawn mower is delivered partly assembled.
The push bar and the grass basket must be
assembled before using the lawn mower. Follow
the instructions step by step and refer to the
pictures when assembling.
Important! Required assembly parts (screws,
cable guides, etc.) or functional parts (e.g. plugs,
wrenches, etc.) can be found in the molded parts
of the packaging or on the equipment.
Warning! Always pull out the safety plug
before making adjustments to the equipment.
Anl_GE_CM_18_33_Li_BL_SPK7_NA.indb 13 Anl_GE_CM_18_33_Li_BL_SPK7_NA.indb 13
EN
Mounting the push bar (Fig. 3-5)
Start by fastening the lower push bars for the left-
hand side (Fig. 3/Item 8) and the right-hand side
(Fig. 3/Item 9) to the mower housing using the
fastening screws and washers (Fig. 3/Item 10,12).
The upper push bar then has to be slid onto the
lower push bars and fastened with screws and
washers (Fig. 4/Item 11,12). There are 2 diff erent
holes on each of the lower push bars for this, to
enable the height of the push bar to be adjusted
to the height of the user. Then fasten the power
cable to the push bar with the cable clips (Fig. 5/
Item 13).
Mounting the catch basket (Fig. 6)
Before you fi t the catch basket you must ensure
that the motor is switched off and the blade is not
rotating. Lift the ejector fl ap (Fig. 6/Item 6) with
one hand. With the other hand, hold the catch
basket by the handle and hook it in from above
(Fig. 6).
Filling level indicator of the grass collector
The grass box is equipped with a fi lling level
indicator (Fig. 1/Item 14). which is opened by the
airfl ow that the lawn mower generates during
operation. If the fl ap closes during mowing,
the grass collecting device is full and must be
emptied. To ensure the proper functioning of the
fi lling level indicator, the holes under the fl ap must
always be kept clean and passable.
Adjusting the cutting height
Caution!
Adjust the cutting height only when the machine
has been switched off and the safety plug has
been pulled out.
The cutting height is adjusted as follows
(Fig. 7):
1. Push the lever (5) downwards.
2. Set the lever (5) to the desired cutting height.
3. Release the lever (5) and check that it is
securely seated in the lock.
Reading off the cutting height
The cutting height can be set between 1" - 2-
5 levels, and can be read off on the scale.
Before you begin to mow, check to ensure that the
blade is not blunt and that none of the fasteners
are damaged. To prevent any imbalance, replace
blunt and/or damaged blades. To carry out this
check, fi rst switch off the motor and pull out the
safety plug.
- 13 -
⁄ " in
1
2
15.11.2023 09:25:40 15.11.2023 09:25:40