Ryobi RY36HTX65A Mode D'emploi page 5

■ If the product is dropped, suffers heavy impact, or begins
to vibrate abnormally, immediately turn off the product
and inspect it for damage or identify the cause of the
vibration. Any damage should be properly repaired or
replaced by an authorised service centre.
■ Operate the product only in temperatures between 0°C
and 40°C.
■ Store the product in a location where the ambient
temperature is between 0°C and 40°C.
■ Injuries may be caused, or aggravated, by prolonged
use of a tool. When using any tool for prolonged periods,
ensure you take regular breaks.
ADDITIONAL BATTERY SAFETY WARNINGS
■ To reduce the risk of fire, personal injury, and product
damage due to a short circuit, never immerse the tool,
battery pack, or charger in fluid or allow fluid to flow inside
them. Corrosive or conductive fluids, such as seawater,
certain industrial chemicals, and bleach or bleach-
containing products, etc., can cause a short circuit.
■ Charge the battery pack in a location where the ambient
temperature is between 10°C and 38°C.
■ Store the battery pack in a location where the ambient
temperature is between 0°C and 40°C.
■ Use the battery pack in a location where the ambient
temperature is between 0°C and 40°C.
TRANSPORTATION AND STORAGE
■ Turn off the product, remove the battery pack, and allow
both to cool down before storing or transporting.
■ Remove all foreign materials from the product. Store the
product in a cool, dry, and well-ventilated area that is
inaccessible to children. For extra safety, store the battery
pack separately from the product. Keep the product away
from corrosive agents such as garden chemicals and de-
icing salts. Do not store the product outdoors.
■ Fit the blade cover before storing the product or during
transportation.
■ For transportation, secure the product against movement
or falling to prevent injury to persons or damage to the
product.
TRANSPORTING LITHIUM BATTERIES
Transport the battery in accordance with local and national
provisions and regulations.
Follow all special requirements on packaging and labelling
when transporting batteries by a third party. Ensure that
no batteries can come in contact with other batteries
or conductive materials while in transport by protecting
exposed connectors with insulating, non-conductive caps or
tape. Do not transport batteries that are cracked or leaking.
Check with the forwarding company for further advice.
MAINTENANCE
■ Use only original manufacturer's replacement parts,
accessories, and attachments. Failure to do so can cause
possible injury, can contribute to poor performance, and
may void your warranty.
■ Servicing requires extreme care and knowledge
and should be performed only by a qualified service
technician. Have the product serviced by an authorised
service centre only.
■ The blades are extremely sharp. To prevent personal
injury, exercise extreme caution when cleaning,
lubricating, fitting, or removing the blade protector.
■ Remove the battery pack before adjusting, maintaining,
or cleaning the product.
■ You may make adjustments and repairs described in this
manual. For other repairs, have the product serviced by
an authorised service centre only.
■ After each use, clean the plastic parts with a soft, dry
cloth.
■ After each use, clean the debris from the blades with a
stiff brush, and then carefully apply a rust preventative
lubricant before refitting the blade protector. The
manufacturer recommends using rust preventative
lubricant spray to apply an even distribution and reduce
the risk of personal injury from contact with the blades.
For information about a suitable spray product, check
with an authorised service centre.
■ Check all nuts, bolts, and screws at frequent intervals
for proper tightness to ensure that the product is in safe
working condition. Any part that is damaged should be
properly repaired or replaced by an authorised service
centre
KNOW YOUR PRODUCT
See page 6.
1. Blade guard
2. Front handle
3. Operator presence switch
4. Handle rotation button
5. Rear handle
6. Trigger
7. Blade
8. HEDGESWEEP debris sweeper
9. Blade cover
10. Battery pack
11. Charger
12. Operator's manual
ANTI-JAM FUNCTION
The RY36HTX65A hedge trimmer has an anti-jam function
to release the blades in case the blades are jammed by big
or hard branches. If the blades are jammed, activate the
anti-jam function by squeezing the front handle, then rapidly
pressing the rear handle trigger twice. The blades will open,
and normal operation can resume.
SYMBOLS ON THE PRODUCT
Safety alert
Read and understand all instructions
before operating the product. Follow all
warnings and safety instructions.
European Conformity Mark
EurAsian Conformity Mark
Ukraine Conformity Mark
5
Original Instructions
EN
FR
DE
ES
IT
NL
PT
DA
SV
FI
NO
RU
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
BG
UK
TR