Instructions For The User 6) Information On The Washing Machine; Instructions For Use And Ordinary Maintenance - grandimpianti WF6 Instructions Pour L'installation Et Mode D'emploi

www.groupdynamics-laundry.com
sales@groupdynamics.lv
Adjustment of this switch is reserved to the
authorised and qualified personnel.
This device consists of a microswitch secured
to the machine's frame, and it is driven by a
flexible rod located inside a metal window
that moves integral with the drum of the
washer. When severe vibrations occur, the
window moves the rod and the safety device
trips (cfr. also alarm "E9" and alarm
description).
During machine installation, after removing
the transportation brackets and with the drum
empty, position the flexible rod at the centre
of the window, so that abnormal tripping of
this safety device is avoided.
For proper positioning, use the screws that
fasten the support of the microswitch and
position this properly.
5.5 WATER CONNECTION
The washing machine is fitted with a warm
water inlet (approximately 60°C) and one
cold water inlet, both of 3/4''.
The incoming water pressure must be
comprised between 0.5 and 5 bar (0.05 and
0.5 MPa).
Prepare wall couplings and, ahead of them,
the appropriate cocks, which must not be
farther than the length of the pipes supplied.
If warm water is not available, mount a T
pipe on the cold-water coupling and connect
both inlets to the cold-water pipe. Both inlets
must anyway be supplied.
Model Capacity of boiler
Mod. 6 55 litres
When the connection is finished make sure
that the pipes are not crushed or blocked.
5.6 STEAM CONNECTION
(steam-heated machines only)
The washing machine is fitted with a 3/4"
steam inlet. The incoming steam pressure
must be between 1 and 6 bar (0.1 and 0.6
MPa). The recommended pressure for best
machine performance is between 4 and 6
bar. If doubts should arise, read the rating
plate data. Steam is intended as saturated
and dry.
The water in the tub can be heated either
directly or indirectly. In the latter instance, a
coupling for the recovery of condensed water
will have to be provided for (diameter 3/4").
If the machine is subjected to ISPESL
inspection, keep all ISPESL documents in
the room where the washing machine is
lodged.
When the connection is finished be sure that
the pipe is not crushed or blocked.
5.7 DRAIN CONNECTION
Make certain that the distance between the
machine drain outlet and the floor drain is
not longer than the drain elbow supplied.
Water is drained through a motor-driven
valve that is open (by gravity) when the
machine is not supplied with electricity.
Therefore, the floor drain must always be
lower than the machine drain outlet. The
diameter of the floor drain must never be
smaller than that of the supplied hose.
Model Drain flow-rate
Mod. 6 80 l/min.
The draining pipe must be able to resist a
temperature of 90°C.
Install a trap between the hose supplied and
the drain.
Check that the hose is not crushed or blocked.
THE GUARANTEE DOES NOT COVER
DAMAGE CAUSED BY INCORRECT
INSTALLATION.
INSTRUCTIONS FOR
THE USER
6. INFORMATION ON THE
WASHING MACHINE
6.1 DESCRIPTION OF THE MACHINE
The machine is composed of the following
main parts (see fig. 1):
1) Hood under which the control circuit is
lodged;
2) Soap dispenser for pre-wash and wash
(foam-damping washing powder) and
for liquid conditioner (foam-damping
type)
3) Loading door;
4) Coin-meter (on coin-operated machines
only);
5) Coin box (on coin-operated machines
only);
6) Drain (8-11-18: 2");
7) Equipotential terminal;
8) Water inlet (3/4").
Description of the keypad
1. YELLOW LED: STOP – The wash
cycle is over or the machine has just
been switched on
2. GREEN LED: SOAK – Soak step
underway (when scheduled)
3. GREEN LED: PREWASH – Prewash
step underway (when scheduled)
4. GREEN LED: WASH - Wash step
16
underway.
5. GREEN LED: RINSE 1/RINSE 3 –
Rinse underway (any between 1 and 3)
6. GREEN LED: SPIN – Final or
intermediate spin underway (led blinks
when slowing down)
7. GREEN LED: DISTRIB. – Distribution
step underway.
8. Cycle selection PUSH-BUTTON
9. Value decrease PUSH-BUTTON
10. Programming PUSH-BUTTON to
change settings and add pauses
11. Value increase PUSH-BUTTON
12. DISPLAY that reads the time to the end
of the cycle and the alarms; when running
the test cycle (the display reads "t") it
reads the water column centimetres
detected by the electronic card.
13. Temperature DISPLAY, shows real
temperature inside the drum
14. Cycle DISPLAY shows presently
selected cycle
15. Lit DOT shows that the heating is on.
6.2 COMPLETE APPLICATION
RANGE
Your washing machine was designed to wash
synthetic fabrics, woollens, cottons and
linens. Choose your cycle by the appropriate
push-button as suggested on the labels
attached to the garments.
6.3 INFORMATION ABOUT THE
ELECTRICAL EQUIPMENT
The built-in electrical equipment is composed
of protection and control devices that are
lodged on a plate, in the upper part of the
machine. The relevant wiring diagrams and
lists are attached further on.
6.4 STATEMENT OF COMPLIANCE
The washing machine described in this
booklet complies with the following
Directives:
The washing machine described in this
booklet complies with the following
Directives and harmonised standards:
73/23 EEC, 93/68 EEC, 89/336 EEC, 92/
31 EEC, 93/68 EEC
EN60335-1, EN60335-2-4, EN60335-2-7,
EN55014, EN61000-3-2, EN61000-3-3,
EN55104.
7. INSTRUCTIONS FOR USE AND
ORDINARY MAINTENANCE
7.1 OPERATION
Make sure that the cold water, warm water
and steam taps are open (the latter applies
only to steam-heated machines).
Turn ON the automatic thermomagnetic
cutoff switch on the wall. If the door is
closed, the machine will then be ready to be
started using the START button on the
machine front panel.