Instructions For The User; Machine Details; Instructions For Use - grandimpianti WR 8 Instructions Pour L'installation Et Mode D'emploi

www.groupdynamics-laundry.com
sales@groupdynamics.lv
- Connect the three phases, the neutral and
earth wires.
- Turn the wall cutoff switch on and then
manually press the spin contactor (C2): if
spinning is clockwise, the phases are
connected correctly; if not, exchange two of
the incoming phases.
IMPORTANT!!! In order to prevent
accidental inversion, let the importance of
phase cyclic direction be known to the
customer, user or person in charge of the
laundry equipment.
5.6 WATER CONNECTION
The washing machine is fitted with a warm
water inlet (approximately 60°C) and a cold
water inlet, both of 3/4''.
The incoming water pressure must be
comprised between 0.5 and 5 bar (0.05 and
0.5 MPa).
Provide for wall couplings at a distance not
exceeding the length of the pipes supplied.
If a warm water source is not available,
mount a T pipe on the cold-water coupling
and connect the warm water inlet to the cold-
water source. Both inlets must anyway be
fed water.
Model Capacity of boiler
Mod. 8 55 litres
Mod.11 80 litres
Mod.18 120 litres
Mod.24 155 litres
Mod.37 215 litres
When the connection is done make sure that
the pipes are not crushed or blocked.
5.7 STEAM CONNECTION
(steam-heated machines only)
The washing machine is fitted with a 3/4"
steam inlet. The incoming steam pressure
must be between 1 and 6 bar (0.01 and 0.6
MPa). The recommended pressure for best
machine performance is between 4 and 6
bar. If doubts should arise, read the rating
plate data. Steam is intended as saturated
and dry.
The water in the tub can be heated either
directly or indirectly. In the latter instance, a
connection for the recovery of condensed
water will have to be provided for (diameter
3/4").
If the machine is subject to ISPESL
inspection, keep all ISPESL documents in
the room where the washer is lodged.
When the connection is done make sure that
the pipes are not crushed or blocked.
5.8 DRAIN CONNECTION
Make certain that the distance between the
machine drain outlet and the floor drain is
not longer than the drain elbow supplied.
Water is drained through a direct-action
motor-driven valve that stays open (by
gravity) when the machine is not powered.
Therefore, the floor drain must always be
below the machine drain outlet. The diameter
of the floor drain must never be smaller than
that of the supplied hose.
Model Drain flow-rate
Mod. 8/11/18 160 l/min.
Mod. 24-37 160 l/min.
The draining pipe must be able to resist a
temperature of 90°C.
Install a trap between the hose supplied and
the drain.
Check that the hose is not crushed or blocked.
5.9 AIR BREAK
The washing machine is equipped with an
air-break device to stop wastewater from
flowing back into the drinkable water system
in the event of a depression. This device has
a rear outlet that may liberate innocuous
steam during heating. Do not close or couple
the air-break outlet.
THE GUARANTEE DOES NOT COVER
DAMAGE CAUSED BY INCORRECT
INSTALLATION.
INSTRUCTIONS FOR
THE USER

6. MACHINE DETAILS

6.1 MACHINE DESCRIPTION
The machine is composed of the following
main parts (see fig. 2 later on):
1) Hood under which the control circuit is
lodged.
2) Soap dispenser for pre-wash and wash
(foam-damping washing powder) and
for liquid conditioner (foam-damping
type).
3) Circular loading door.
4) Coin-meter (on coin-operated machines
only).
5) Coin box (on coin-operated machines
only).
6) Drain (8-11-18-24-33; 75 mm).
7) Equipotential terminal.
8) Air break.
9) ¾ Water intake
Description of the keypad
1. YELLOW LED: STOP - The wash cycle
is over or the machine has just been
switched on
2. GREEN LED: SOAK- Soak step
underway (when scheduled)
3. GREEN LED: PREWASH Prewash step
underway (when scheduled)
16
4. GREEN LED: WASH Wash step
underway.
5. GREEN LED: RINSE 1/RINSE 3 -
Rinse underway (any between 1 and 3)
6. GREEN LED: SPIN - Final or
intermediate spin underway (led blinks
when slowing down)
7. GREEN LED: DISTRIB. Distribution
step underway
8. Cycle selection BUTTON
9. Value down BUTTON
10. Programming BUTTON: to change
settings and schedule pauses
11. Value up BUTTON
12. DISPLAY that reads the time to the end
of the cycle and the alarms; when running
the test cycle (the display reads "t") it
reads the water column centimetres
detected by the electronic card.
13. Temperature DISPLAY, shows real
temperature inside the drum
14. Cycle DISPLAY, shows presently
selected cycle type
15. DOT, when lit it indicated that the
heating is on.
6.2 APPLICATION RANGE
Your washing machine was designed to
wash synthetics, woollens, cottons and
linens. Choose your cycle by the appropriate
button as suggested on the labels attached to
the garments to be washed.
6.3 INFORMATION ABOUT THE
ELECTRICAL SYSTEM
The built-in electrical system is composed
of protection and control devices duly lodged
on a plate at the top part of the machine. The
relevant diagrams and lists appear later on in
this manual.
6.4 DOCUMENTS THAT CERTIFY
MACHINE CONFORMITY
The washing machine described in this
booklet complies with the following
directives and harmonised standards:
73/23 EEC, 93/68 EEC, 89/336 EEC, 92/31
EEC, 93/68 EEC
EN60335-1; EN60335-2-4; EN60335-2-7
EN55014; EN61000-3-2 ; EN61000-3-3;
EN55104
7. INSTRUCTIONS FOR USE AND
ORDINARY MAINTENANCE
7.1 OPERATION
Make sure that the cold water, warm water
and steam taps are open (the latter applies
only to steam-heated machines).
Turn ON the automatic thermomagnetic
cutoff switch on the wall. If the door is
closed, the machine will be ready to be
started using the START button on the
machine front panel.
To select the cycle, open the door by the
appropriate handle and press the "P" button.
The relevant display will read the
corresponding program number: to confirm
the selection just close the door. Every time