Publicité
Les langues disponibles
Les langues disponibles
Working behaviour and working technique (10 – 12)
2. Tilt cutter head (09/2) to the desired angle
and allow to engage (09/b).
3. Release the locking button.
7.7
Checking the charge status of the
rechargeable battery
Charge status indicator (01/4) is located on the
top of the basic appliance.
It has three segments. The segments light up or
flash, depending on the battery charge status.
Segment
3 segments lit:
2 segments lit:
1 segment lit:
1 segment flashing:
8 WORKING BEHAVIOUR AND
WORKING TECHNIQUE (10 – 12)
■
Switch on the appliance before approaching
the grass to be cut and then lower slowly to
avoid overloading.
■
Tilt the appliance slightly forwards (approx.
30°) to mow with the tip of the cutting line.
Walk forwards slowly (10).
■
When mowing, swivel the appliance evenly to
the right and left (11).
■
Long grass must be mown in several passes.
Always proceed from top to bottom (11).
■
The appliance cuts best at very high speed.
Therefore, do not overload the appliance by
cutting long grass.
■
If the appliance is overloaded in long grass,
the line will be blocked. Immediately lift the
appliance so it releases. Otherwise, the mo-
tor could be permanently damaged.
■
Do not move the appliance directly against
hard obstacles (e.g. walls), but mow side-
ways. This protects the cutting line (12).
■
Keep the appliance away from delicate
plants. Fold the plant protection bar into the
horizontal position.
■
Allow the appliance to rest on the jockey
wheel when trimming lawn edges. This will
prevent excessive wear of the cutting line
when trimming lawn edges.
443172_b
Battery charge level
Rechargeable battery
fully charged.
Rechargeable battery
2/3 charged.
Rechargeable battery
1/3 charged.
Rechargeable battery
almost flat. The appli-
ance will switch off
shortly.
9 MAINTENANCE AND CARE
WARNING! Danger of cuts and lacera-
tions. Danger of cuts and lacerations when
reaching into sharp-edged, moving appliance
parts and into cutting tools.
■
Before maintenance, care and cleaning work,
always switch off the appliance. Remove the
rechargeable battery.
■
Always wear protective gloves during mainte-
nance, care and cleaning work.
NOTE Repair work is only allowed to be car-
ried out by expert workshops or our service cen-
tres.
■
Do not get the appliance wet or expose it to
moisture. Do not spray with water.
■
After each use, clean the housing and cutting
blades with a brush or cloth. Do not use wa-
ter and/or aggressive cleaning agents or sol-
vents - risk of corrosion and damage to the
plastic parts.
■
After every use, remove the rechargeable bat-
tery and inspect the appliance for damage.
■
Do not use the appliance if the blade of the
line cutter is missing or damaged.
■
Always keep the guard plate, spool head and
motor clear of mowing residues.
■
Inspect all bolts for tightness.
■
Inspect the electrical contacts of the appli-
ance for corrosion, clean with a fine wire
brush if necessary and then spray with a con-
tact spray.
9.1
Changing the spool (13)
Replacement spool: set of 2 (Article No.: 113349)
Precondition: The appliance must be switched off
and the rechargeable battery removed from the
appliance.
Inserting and removing the spool
1. Press (13/a) the two unlocking buttons (13/1)
at the same time and remove cover (13/2).
2. Remove empty spool (13/3).
3. Insert (13/b) a new spool (13/4). Ensure that
spring (13/5) is installed again.
4. Thread the cutting line outwards through
opening (13/6) of the spool head.
5. Fit cover (13/2) and press on until it engages.
6. Install the rechargeable battery in the appli-
ance.
27
Publicité
