Publicité
Les langues disponibles
Les langues disponibles
ELECTriCAL CoNNECTioNS
Check that the electrical system to which the machine is
connected is earthed in compliance with current safety
regulations and that the current socket is in perfect con-
dition.
The electrical system must be fitted with a magnetother-
mal protective device to safeguard all conductors from
short circuits and overload.
The selection of this device should be in line with the
following electrical specifications of the machine stated
on the motor.
NoTE: Your plunge cut saw's electrical system is equipped
with an undervoltage relay which automatically opens the
circuit when the voltage falls below a minimum pre-est-
ablished limit and which prevents the self-reset of ma-
chine functions when voltage returns to normal levels.
If the machine stops involutarily, do not be allarmed.
Make sure that there has not been a voltage failure in the
electrical system.
ADJUSTiNG
Caution: Prior to carrying out one of the following adjust-
ment steps, switch the machine off and unplug the mains
plug.
Cutting depth adjustment, Fig. 2
The cutting depth can be adjusted from 0 to 45 mm.
Unfasten the cutting depth adjustment screw (6) and set
the required depth using the scale (7) and retighten the
screw.
The dimentions on the rail shows the cutting depth with-
out rail.
Mitre settings, Fig. 3
The mitre square can be set from 0° to 45°.
Unfasten the mitre adjustment screws (8) on both sides,
set the desired mitre square on the scale (9) and retight-
en both screws.
Saw blade replacement, Fig. 4, 5, 6
Caution: Before you are going to make the saw blade change,
switch off the machine and unplug the power cord.
1 Press the plunge trigger (3), bring the saw blade into
the blade-change position (Adjustment screw for depth
of cut shall be adjusted to 25mm) and insert the hex
wrench into the blade locking screw (17).
2 Press on the shaft lock (13) and rotate the saw blade
(10) until the lock clicks into place.
3 Hold down the locking shaft (13) and open the blade
locking screw (17) counter clockwise, while keeping
the blade in the blade-changing position.
4 Remove the outer flange (16) and the saw blade (10).
(Caution: risk of injuries, wear protective gloves)
5 Insert the new blade and flange.
6 Screw in and tighten the saw blade locking screw while
keeping the shaft locking mechanism pressed again.
7 Set the plunge saw to its original position.
16
operations
After having performed all the above procedures and
opera tions, you may begin cutting.
ATTENTioN: Always keep hands away from the cutting
area and do not try to approach it when the machine is
running.
Switching the product on/off, Fig. 1
To switch the plunge-cut saw on, press the on/off switch
(4). To switch off, release the on/off switch (4).
operating and holding the plunge-cut saw, Fig. 8
1 Secure the work piece so that it cannot get displaced
or moved while sawing.
2 Only move the saw forwards.
3 Grip the saw tightly with both hands ensuring that one
hand is placed on the main handle and the other on
the front handle.
4 When using a guide rail, it must be fastened with screw
clamps.
5 Make sure the power cable is not placed in the sawing
direction.
Sawing
1 Place the front part of the machine onto the work piece.
2 Switch the machine on using the on/off switch (4).
3 Press the plunge-cut trigger (3).
4 Push the saw downwards to reach the sawing depth.
5 Push the saw forward evenly.
6 After finishing the sawing cut, switch the machine off
and move the saw blade upwards.
Plunge-cuts, Fig. 9
1 Place the saw onto the work piece.
2 Place the cutting indicator with the rear arrow (A) on
the deepest plunge-cut position.
3 Switch the machine on and push the saw downwards
until you reach the set cutting depth.
4 Move the saw forwards until the cutting indication (C)
has reached the marked point.
5 After completion of the plunge-cut, move the saw blade
upwards and switch the saw off.
Cutting with rails (otional)
1 Place the machine in the guide rails. can be readjusted
using the hex driver included in the delivery, when
there is the risk of the adjusting screws releasing by
themselves.
2 Turn on the machine by pressing the on/off switch (4).
3 Press the dip trigger (3).
4 Press the saw downwards to reach the sawing depth.
During first use the rubber lip is sawn off and thus
splitter protection is guaranteed up to the saw blade.
5 Push the saw uniformly forwards.
6 Turn off the machine and tilt the saw blade to the top
when the saw cutting is complete.
Sawing with dust suction
Connect the suction hose to the exhaust nozzle - Ø 38
mm (12).
Publicité
