Publicité
Les langues disponibles
Les langues disponibles
objects and plants.
_
Only use the appliance for working dry
grass.
_
The appliance will automatically feed the
cutting line during use.
SWITCHING ON AND OFF
If the trimmer is to be used for the first time, check
that the nylon line touches or passes over the
cutting blade. The nylon line will be cut
automatically when turn on the switch to the
maximum length. If it does not reach the necessary
length, push the head of spool with your finger while
pulling the lines .
Insert the plug into the extension cable and attach it
to the handle. Pressure the switch and make the
trimmer turn at no load; thus, the line length is
automatically adjusted. Only approach the
implement to the grass to be cut while it is in
operation, i.e. while the switch is pressed down.
Caution! Before turn on the switch, take the
blade cover away.
To cut long grass, take several small cuts. Never cut
wet or very damp grass. The line has to be
protected against premature wear caused by hard
obstacles; for this purpose, keep the trimmer away
from hard surfaces using the guard's edge as a
protection. A short or worn line will reduce cutting
capacity. So, to restore the line to its optimum
length, push the implement to the ground while it is
running; this way, the line will automatically be the
correct length .
CAUTION! The short or worn line cuts less
efficiently therefore, to improve its operations,
unplug the electrical supply and repeat the
operation described in the beginning of the chapter.
These make sure that everything is functioning
properly and to familiarize yourself with the grass
trimmer.
CAUTION! After switching off, the nylon line will
continue to rotate for a few more seconds.
REPLACEMENT OF THE LINE SPOOL
Unplug from the socket.
Turn upside down the machine with the guard
facing upwards.
Hold with one hand the motor fan (1) firmly and
with the other hold the spool holder (2). Push
the clips of the spool holder both side down
and pull it out of the motor fan.
Extract the empty spool (3) and clean the
inside of the spool holder carefully removing all
dust and grass residues.
Insert now the new spool in the motor fan and
push the end of line through the lateral holes
provided on the motor fan.
Push the spool holder on and fasten it
securely.
Re-establish the length of the nylon line by
pushing the head of spool holder and pull the
line ends out to the desired length (approx. 10
cm).
CAUTION! Under no circumstances wind extra line
on the empty spool but instead replace it with a new
one, the same as the original. The use of line with
different characteristics to those of the original can
permanently damage the grass trimmer as well as
annulling the terms of the guarantee.
MAINTENANCE
maintenance to the machine,
always unplug the machine.
Regular cleaning and maintenance of you grass
trimmer will ensure efficiency and prolong the
life of your machine.
After each cutting operation, take apart and
clean out the grass and soil from; the spool and
its slot, the whole trimmer and in particular the
guard.
During operation, keep the air slots clean and
free of grass.
Only use a cloth soaked with hot water and a
soft brush to clean the grass trimmer.
Do not spray or wet the appliance with water.
Do not use detergents or solvents as these
could ruin the trimmer. The parts in plastic can
easily be damaged by chemical agents.
If the line cutting blade no longer cuts or breaks,
have this replaced by contacting an authorized
service centre.
For repairs which have not been explained in
these instructions, contact an authorized
service centre.
After use, disconnect the machine from the
mains and check for damage;
When not in use store the machine out of the
reach of children;
Inspect and maintain the trimmer regularly.
Mains powered trimmers should only be
repaired by an authorized repairer ;
User may carry out maintenance and
adjustments. Please refer to the part of
REPLACEMENT OF THE SPOOL OF NYLON
WIRE.
Use
only
manufacturers
replacement parts and accessories. (Line:φ
1.2 )
TROUBLE-SHOOTING
maintenance to the machine,
always unplug the machine.
If the grass trimmer vibrates: remove the spool
and clean its slot carefully removing any grass
and so forth. If vibration persists after
reassembly, replace the spool with a new one.
In the event of the problem not disappearing,
have the trimmer checked at an authorized
service center.
If the grass trimmer does not start: check all the
electrical connections; make sure the safety
circuit-breaker has not been activated; check
that no fuse has blown in your electrical system.
If after the above checks, the grass trimmer still
Before performing
recommended
Before performing
20
Publicité
