Milwaukee K500ST Notice Originale page 7

Masquer les pouces Voir aussi pour K500ST:

Notice originale (64 pages)

page de 49

/ 49
Signets

Les langues disponibles

doing so could trigger a sudden recoil with a high reactive force.

Determine why the insertion tool stalled and rectify this, paying

heed to the safety instructions.

Possible causes may be:

• it is tilted in the workpiece to be machined

• breakage of the material to be used

• the power tool is overloaded

Do not reach into the machine while it is running.

The insertion tool is sharp-edged and can become hot during use.

WARNING! Danger of cuts and burns

when handling the insertion tools

when setting the device down

Wear protective gloves when handling insertion tools.

Chips and splinters must not be removed while the machine is

running.

Always disconnect the plug from the socket before carrying out

any work on the machine.

OPERATION

Cold Starting

If this tool is stored for a long period of time or at cold tempera-

tures, it may not hammer initially because the lubrication has

become stiff.

To warm up the tool

1. Insert and lock a bit or chisel into the tool.

2. Pull the trigger and apply force to the bit or chisel against a

concrete or wood surface for a few seconds. Release the trigger.

3. Repeat until the tool starts hammering. The colder the tool is,

the longer it will take to warm up.

SPECIFIED CONDITIONS OF USE

The hammer can be used for chiselling in stone and concrete.

MAINS CONNECTION

Appliances used at many different locations including wet room

and open air must be connected via a residual current device (FI,

RCD, PRCD) of 30mA or less.

Connect only to single-phase AC system voltage as indicated on

the rating plate. It is also possible to connect to sockets without an

earthing contact as the design conforms to safety class II.

Only plug-in when machine is switched off.

MAINTENANCE

The ventilation slots of the machine must be kept clear at all

times.

If the supply cord of this appliance is damaged, it must only be

replaced by a repair shop appointed by the manufacturer, to avoid

hazardous situations.

Use only Milwaukee accessories and Milwaukee spare parts.

Should components need to be replaced which have not been

described, please contact one of our Milwaukee service agents

(see our list of guarantee/service addresses).

If needed, an exploded view of the tool can be ordered. Please

state the Article No. as well as the machine type printed on the

label and order the drawing at your local service agents or directly

at: Techtronic Industries GmbH, Max-Eyth-Straße 10, 71364 Win-

nenden, Germany.

English

SYMBOLS

Please read the instructions carefully before starting the

machine.

CAUTION! WARNING! DANGER!

Always disconnect the plug from the socket before carrying

out any work on the machine.

Always wear goggles when using the machine.

Wear ear protectors.

Wear a suitable dust protection mask.

Wear gloves!

Accessory - Not included in standard equipment.

Do not dispose of waste electrical and electronic equipment

as unsorted municipal waste. Waste electrical and electronic

equipment must be collected separately. Waste light sources

have to be removed from equipment. Check with your local

authority or retailer for recycling advice and collection point.

According to local regulations, retailers may have an obliga-

tion to take back waste electrical and electronic equipment

free of charge. Your contribution to re-use and recycling of

waste electrical and electronic equipment helps to reduce

the demand of raw materials. Waste electrical and electronic

equipment contain valuable, recyclable materials, which can

adversely impact the environment and the human health, if

not disposed of in an environmentally compatible manner.

Delete personal data from waste equipment, if any.

Class II tool. Tool in which protection against electric

shock does not rely on basic insulation only, but in which

additional safety precautions, such as double insulation

or reinforced insulation, are provided. There being

no provision for protective earthing or reliance upon

installation conditions.

No-load speed

Voltage

AC Current

European Conformity Mark

British Conformity Mark

Ukraine Conformity Mark

EurAsian Conformity Mark

EC-DECLARATION OF CONFORMITY

We declare under our sole responsibility that the product

described under "Technical Data" fulfills all the relevant provisions

of the directives

2011/65/EU (RoHS)

2006/42/EC

2014/30/EU

and the following harmonized standards have been used

EN 62841-1+A11:2022

EN 62841-2-6:2020 +A11:2020

EN IEC 55014-1:2021

EN IEC 55014-2:2021

EN IEC 61000-3-2:2019+A1:2021

EN 61000-3-3:2013+A1:2019+A2:2021

EN IEC 63000:2018

Measured values determined according to 2000/14/EC at the user's

ear. Conformity assessment procedure according to Annex VI.

EU Notified Body:

DEKRA Testing and Certification GmbH,

Handwerkstraße 15, 70565 Stuttgart

Location Certification Body, Dinnendahlstr. 9, 44809 Bochum,

Germany

Notified Body number: 0158

Measured sound power level: 97,6 dB (A

Guaranteed sound power level: 100,0 dB (A)

Winnenden, 2023-01-20

Alexander Krug / Managing Director

Authorized to compile the technical file

Techtronic Industries GmbH

Max-Eyth-Straße 10, 71364 Winnenden, Germany

GB-DECLARATION OF CONFORMITY

We declare as the manufacturer under our sole responsibility

that the product described under „Technical Data" fulfills all the

relevant provisions of the following Regulations

S.I. 2012/3032 (as amended), S.I. 2008/1597 (as amended),

S.I. 2016/1091 (as amended) and that the following designated

standards have been used:

BS EN 62841-1+A11:2022

BS EN 62841-2-6:2020 +A11:2020

BS EN IEC 55014-1:2021

BS EN IEC 55014-2:2021

BS EN IEC 61000-3-2:2019+A1:2021

BS EN 61000-3-3:2013+A1:2019+A2:2021

BS EN IEC 63000:2018