Milwaukee K500ST Notice Originale page 6

IV
4 4
GB
TECHNICAL DATA
Chipping Hammer
Production code
Rated input
Output
Rate of percussion under load max.
Impact energy per stroke according to EPTA-Procedure 05/2009
Chuck neck diameter
Weight according EPTA-Procedure 01/2014
Noise information
Measured values determined according to EN 62841. Typically, the A-weighted noise levels of the tool are:
Sound pressure level (Uncertainty K=3dB(A))
Sound power level (Uncertainty K=3dB(A))
Wear ear protectors!
Vibration information
Vibration total values (triaxial vector sum) determined according to EN 62841
Chiselling:
Vibration emission value a
h, Cheq
Uncertainty K=
WARNING!
The vibration and noise emission level given in this information sheet has been measured in accordance with a standardized test given in
EN 62841 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration and noise emission level represents the main applications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained, the vibration and noise emission may differ. This may significantly increase
the exposure level over the total working period.
An estimation of the level of exposure to vibration and noise should also take into account the times when the tool is switched off or when
it is running but not actually doing the job. This may significantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the effects of vibration and/or noise such as: maintain the tool and the
accessories, keep the hands warm, organization of work patterns.
WARNING Read all safety warnings, instructions,
illustrations and specifications provided with this power
tool. Failure to follow the warnings and instructions may result in
electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
HAMMER SAFETY WARNINGS
Safety instructions for all operations
Wear ear protectors. Exposure to noise can cause hearing loss.
Use auxiliary handle(s), if supplied with the tool. Loss of
control can cause personal injury.
Hold the power tool by insulated gripping surfaces, when
performing an operation where the cutting accessory may
contact hidden wiring or its own cord. Cutting accessory con-
tacting a "live" wire may make exposed metal parts of the power
tool "live" and could give the operator an electric shock.
Safety instructions when using long drill bits with rotary hammer
Always start drilling at low speed and with the bit tip in contact
with the workpiece. At higher speeds, the bit is likely to bend if al-
lowed to rotate freely without contacting the workpiece, resulting
in personal injury.
K 500 ST K 500 ST
220-240 V 110-120 V
4431 81 07... 4433 46 07...
4439 21 07... ... 000001-999999
... 000001-999999
1100 W 1100 W
550 W 550 W
3000 min 3000 min
-1 -1
7,5 J 7,5 J
66 mm 66 mm
5,9 kg 5,9 kg
97,0 dB (A) 94,0 dB (A)
105,0 dB (A) 102,0 dB (A)
12,8 m/s 2 11,3 m/s 2
1,5 m/s 2 1,5 m/s 2
Apply pressure only in direct line with the bit and do not apply ex-
cessive pressure. Bits can bend causing breakage or loss of control,
resulting in personal injury.
Additional Safety and Working Instructions
Use personal protective equipment. Always wear eye protection.
Protective equipment such as a dust mask, non-skid safety shoes,
hard hat or hearing protection used for appropriate conditions will
reduce personal injuries.
The dust produced when using this tool may be harmful to health.
Do not inhale the dust. Use a dust absorption system and wear a
suitable dust protection mask. Remove deposited dust thoroughly,
e.g. with a vacuum cleaner.
Do not machine any materials that present a danger to health (e.g.
asbestos).
When working in walls ceiling, or floor, take care to avoid electric
cables and gas or waterpipes.
Clamp your workpiece with a clamping device. Unclamped workpi-
eces can cause severe injury and damage.
Keep mains lead clear from working range of the machine. Always
lead the cable away behind you.
Switch the device off immediately if the insertion tool stalls! Do
not switch the device on again while the insertion tool is stalled, as
English
GB