Proper Use Of The Product; Scope Of Delivery - EUFAB AMBER 4 Manuel De L'opérateur

Bicycle rack „AMBER IV" for trailer tow bar
OVERVIEW

1. PROPER USE OF THE PRODUCT

2. SCOPE OF DELIVERY

3. SPECIFICATIONS
3.1 TOW BAR REQUIREMENTS
4. SAFETY NOTES AND IMPORTANT INFORMATION
5. OPERATING INSTRUCTIONS
5.1 MOUNTING THE BICYCLE RACK
5.1.1 MOUNTING THE WHEEL RAILS ON THE BASE FRAME
5.1.2 MOUNTING THE LAMP MOUNTS
5.1.3 SECURING THE LIGHT MOUNT TO THE BASE FRAME
5.1.4 MOUNTING THE U-BRACKET
5.1.5 MOUNTING THE FRAME HOLDER
5.1.6 MOUNTING THE LICENSE PLATE HOLDER
5.1.7 INSERTING THE LICENSE PLATE
5.1.8 LAYING ELECTRICAL CABLES
5.1.9 ATTACHING THE PLASTIC COVERS
5.1.10 MOUNTING THE SHORT TENSIONING STRAPS
5.2 MOUNTING THE BICYCLE RACK ON THE TRAILER TOW BAR
5.3 MOUNTING THE BICYCLES TO THE RACK
5.4 USING THE TENSION-RELIEF STRAP
5.5 FOLDING OUT THE BICYCLE RACK
5.6 FOLDING THE BICYCLE RACK UP
6. MAINTENANCE AND CARE
7. NOTES FOR ENVIRONMENTAL PROTECTION
8. CONTACT INFORMATION
WARNING
Read the operating instructions through carefully prior to initial use and observe all of the safety notes!
Not observing such may lead to personal injury, damages to the device or your property!
Store the original packaging, the receipt and these instructions so that they may be consulted at a later date!
Prior to initial use check the contents of the packaging to ensure that they are in perfect condition and complete!
1. PROPER USE OF THE PRODUCT
The AMBER IV bicycle rack is mounted to the trailer tow bar of a car and is designed for the transportation of up to two bicycles.
Intended use also includes the observation of all information provided in these operating instructions, particularly the observance of safety instructions. Any
other use is considered improper and can lead to property damage or personal injury. EAL GmbH assumes no liability for damage resulting from improper use.
2. SCOPE OF DELIVERY
1 x Base frame
8 x Wheel rail
1 x Lamp mount set
1 x U-bracket
2 x Frame holder, short
1 x Frame holder, long
3. SPECIFICATIONS
Dead weight: 19.5 kg
Payload: 30 kg (at 50 kg supporting load)
40 kg (at 60 kg supporting load)
max. 55 kg (at 75 kg supporting load)
max. 60 kg (at 90 kg supporting load)
Material: Steel
Electrical connection: 13-pin connector
3.1 TOW BAR REQUIREMENTS
• The trailer tow bar must be approved in its construction.
• Ball and ball rod must have been forged in one piece.
• Only mount the bicycle rack to a coupling of steel St52-3, grey cast iron GGG52 or higher quality.
• The D-value of the tow bar ball must be at least 7.6 kN
• Never mount the rack to a tow bar made of aluminium, other light metals or plastic.
1 x Frame holder, wheel to wheel
4 x Plastic cover
12 x Tensioning strap, short
1 x Tensioning strap, long
1 x Tension-relief strap, two-piece
16 x Lock screw M6 x 50
16 x Washer 17,8 x 6,5 x 1,1
16 x Nut M6
1 x Cross-headed screw M5 x 12
1 x Washer 9,8 x 5,4 x 0,9
1 x Spring washer 8,4 x 5,5 x 1,5
2 x Cross-headed screw M5 x 35
2 x Spring washer 8,1 x 5,5 x 1,2
2 x Washer 9,7 x 5,3 x 0,9
2 x Lock screw M8 x 60
2 x Washer 15,8 x 8,5 x 1,1
2 x Knob nut M8
Cable tie
9
9
9
9
10
11
11
11
11
11
11
11
11
12
12
12
12
12
13
13
14
14
14
14
14
9