Titan ED655 Mode D'emploi page 3

Important Safety Information
• High-pressure spray is able to inject toxins into the body and
cause serious bodily injury. In the event that injection occurs,
seek medical attention immediately.
• Check hoses and parts for signs of damage, a leak can inject
material into the skin. Inspect hose before each use. Replace
any damaged hoses or parts. Only use TITAN original-high-
pressure hoses in order to ensure functionality, safety and
durability.
• This system is capable of producing 2800 PSI / 193 Bar. Only
use replacement parts or accessories that are specified by the
manufacturer and that are rated a minimum of 2800 PSI. This
includes spray tips, nozzle guards, guns, extensions, fittings,
and hose.
• Always engage the trigger lock when not spraying. Verify the
trigger lock is functioning properly.
• Verify that all connections are secure before operating the
unit.
• Know how to stop the unit and bleed pressure quickly. Be
thoroughly familiar with the controls. Pressure will not be
released by turning off the motor. The PRIME/SPRAY valve
or pressure bleed valve must be turned to their appropriate
positions to relieve system pressure. Refer to PRESSURE
RELIEF PROCEDURE described in the pump manual.
• Always remove the spray tip before flushing or cleaning the
system.
NOTE TO PHYSICIAN:
Injection into the skin is a traumatic injury which can lead
to possible amputation. It is important to treat the injury as
soon as possible. DO NOT delay treatment to research toxicity.
Toxicity is a concern with some coatings injected directly
into the blood stream. Consultation with a plastic surgeon or
reconstructive hand surgeon may be advisable.
WARNING: HAZARDOUS VAPORS
Paints, solvents, insecticides, and other materials can
be harmful if inhaled or come in contact with the body.
Vapors can cause severe nausea, fainting, or poisoning.
PREVENTION:
• Use a respirator or mask if vapors can be inhaled. Read all
instructions supplied with the mask to be sure it will provide
the necessary protection.
• Wear protective eyewear.
• Wear protective clothing as required by coating manufacturer.
WARNING: GENERAL
Can cause severe injury or property damage.
PREVENTION:
• Always wear appropriate gloves, eye protection, clothing and
a respirator or mask when painting.
• Do not operate or spray near children. Keep children away
from equipment at all times.
• Do not overreach or stand on an unstable support. Keep
effective footing and balance at all times.
• Stay alert and watch what you are doing.
• Do not operate the unit when fatigued or under the influence
of drugs or alcohol.
• Do not kink or over-bend the hose. Airless hose can develop
leaks from wear, kinking and abuse. A leak can inject material
into the skin.
© Titan Tool. All rights reserved.
• Do not expose the hose to temperatures or pressures in excess
of those specified by manufacturer.
• Do not use the hose as a strength member to pull or lift the
equipment.
• Use lowest possible pressure to flush equipment.
• Follow all appropriate local, state and national codes
governing ventilation, fire prevention and operation.
• The United States Government Safety Standards have been
adopted under the Occupational Safety and Health Act
(OSHA). These standards, particularly part 1910 of the General
Standards and part 1926 of the Construction Standards should
be consulted.
• Before each use, check all hoses for cuts, leaks, abrasion
or bulging of cover. Check for damage or movement
of couplings. Immediately replace hose if any of those
conditions exist. Never repair a paint hose. Replace with a
conductive high-pressure hose.
• Do not spray outdoors on windy days.
• Always unplug cord from outlet before working on equipment
(electric models only).
IMPORTANT: The diaphragm pump is provided with a thermally
protected automatic reset. If an overload occurs the thermally
protected automatic reset disconnects the motor from the power
supply.
• The motor will restart without warning when the protector
automatically resets.
• Always disconnect the motor from the power supply before
working on the equipment.
• When the thermally protected automatic reset disconnects
the motor from the power supply, relieve pressure by turning
the PRIME/SPRAY valve to PRIME.
• Turn the pump ON/OFF switch to OFF.
NOTE: The cause of the overload should be corrected
before restarting. Refer to the Troubleshooting
section.
NOTE: Make sure to check for grounding continuity after
service is performed on any electrical components.
Use an ohmmeter to determine that there is
continuity between accessible dead-metal parts
of the product and the grounding blade of the
attachment plug.
Specifications
Weight .....................................................27 lbs
Capacity ..................................................Up to .35 gallon (1.25 liters) per
Power source ........................................Electric motor, totally enclosed, fan
Power requirement.............................15 amp minimum circuit on 115
Generator ...............................................5000 Watts
Spraying pressure ...............................Up to 2800 PSI
Capabilities ............................................Sprays a variety of oil-based and
3
minute
cooled
VAC, 60 Hz current.
latex paints, primers, and stains
English