Preparing Coffee; Steam Distribution; Drawing Hot Water; Turning Off The Machine - Bezzera BZ13 Manuel D'instructions

between 1 and 1.2 bar (0.1 - 0.12 MPa), DEPID-
PMPID version the temperature indicated on the
PID (Fig. 01; pos. 11B) between 90 and 95 °C
(temperature suggested by the factory) open the
steam tap (Fig. 01; pos. 9) and discharge the
steam 2 or 3 times into the discharge basin.
PM VERSION
The yellow light (Fig. 01; pos. 3), if turned on
indicates that the machine is working correctly, if
turned off means insufficient water in the tank.
DEPID-PMPID VERSION
The PID (Fig. 01; pos. 11b), if turned on indicates
that the machine is working correctly, if turned off
means insufficient water in the tank.

5.3 Preparing coffee

1) Remove the filter holder (Fig. 01; pos. 6) from
the distribution unit (Fig. 01; pos. 5).
2) Load the filter holder with ground coffee, press
the coffee down taking care to not dirty the
edge of the filter holder.
3) Reattach the filter holder in its housing.
PM-PMPID VERSION
4) Start up coffee distribution by pressing the
distribution button (Fig. 04; pos. a).
5) Stop distribution when the desired quantity is
reached, by pressing the distribution button
again.
DEPID VERSION
4) Use the coffee distribution keypad (Fig. 05),
by pressing one of the keys, depending on the
desired dose.
To change dose programming, follow the
instructions in paragraph 5.7 of this booklet.
The machine is set for continuous distribution:
press the key "BEZZERA" (Fig. 05; pos. c) to start
up distribution, press again to stop..
Warnings:
- Do not remove the filter holder full of coffee when
All manuals and user guides at all-guides.com
- Do not touch the metal part of the filter holder
- The standard doses for the filters are 6/8

5.4 Steam distribution

1) To avoid liquids being sucked into the boiler,
2) Insert the steam nozzle (Fig. 01; pos. 10) in the
3) Press down and hold the steam tap knob (Fig.
4) Once steam has been distributed, release
Warning: Do not touch the steam nozzle directly
as it is hot.

5.5 Drawing hot water

1) Place the water container under the nozzle (Fig.
2) Press down and hold the water tap knob (Fig.
3) Once water has been distributed, release the
Warning: Do not touch the water distributor tap
directly as it is hot.

5.6 Turning off the machine

Turn the main switch (Fig. 01; pos. 1) to position
"0" and check that the green light PM version (Fig.
01; pos. 2), red light DEPID-PMPID version (Fig.
01; pos. 2a) has turned off.
Should the machine be off for long periods:
1) Empty the tank.
2) Unplug from power supply.
3) Replace the machine in a dry, weather-resist-
27
MOD. BEZZERA BZ13
the machine is working, as it is pressurised.
directly as it is hot.
grams for a dose and 12/14 grams for two
doses.
discharge the steam by turning the tap knob
(Fig. 01; pos. 9).
container of the liquid to be heated.
01; pos. 9), lifting the lever the tap will remain
in open position (Fig. 06). The amount of
steam distributed is proportional to the opening
of the tap; the more the tap is opened, the more
steam will be distributed.
knob, remove liquid container and clean the
steam nozzle immediately with a damp cloth to
remove heated liquid residues.
01; pos. 8).
01; pos. 7) to draw the amount of water
required.
knob.
ant environment of exclusive access.
(Fig. 06)