Mixer Operations; Basic Operations - Pioneer DJM-700-S Mode D'emploi

01_DJM-700_En.book 13 ページ ２００７年７月１０日 火曜日 午後８時４１分

MIXER OPERATIONS

MIXER OPERATIONS

BASIC OPERATIONS

2
3
TRIM
4
HI, MID, LOW
5
6
1 Set rear panel POWER switch to ON.
2 Set the input selector switch for the desired channel to
choose the connected component.
• CH1: Set to [ CD ] or [ LINE ].
CH2: Set to [ CD ] or [ PHONO ].
CH3/4: Set to [ LINE ] or [ PHONO ].
3 Use the TRIM dial to adjust the input level.
4 Use the channel equalizer dials (HI, MID, LOW) to adjust the
tone.
5 Use the channel fader lever to adjust the sound volume of
the selected channel.
6 To use the cross fader on the selected channel, set the CROSS
FADER ASSIGN switch to either cross fader channel A or
channel B, and operate the cross fader lever.
• When not using the cross fader, set the CROSS FADER
ASSIGN switch to [ THRU ].
7 Use the MASTER LEVEL dial to adjust the overall sound
volume.
8 Use the BALANCE dial to adjust the sound balance between
right and left.
Microphone input
Headphones output
[Selecting Stereo or Monaural]
When the MONO/STEREO switch is set to [ MONO ], the master
1 POWER
output becomes a monaural combination of L+R channels.
[Microphone Input]
7
1
MASTER
LEVEL
2
8
3
BALANCE
[Booth Monitor Output]
1
[Headphones Output]
1
2
3
Booth monitor output
4
MONO/
STEREO
Fader curve
To use a microphone, set the MIC switch to [ON] or [TALK
OVER].
• When the switch is set to [ TALK OVER ], any time a sound of
over –15 dB is detected by the microphone, the output for all
sound sources other than the microphone are attenuated by
20 dB.
Use the MIC 1 LEVEL dial to adjust the sound volume of
MIC 1, and use the MIC 2 LEVEL dial to adjust the sound
volume of MIC 2.
Use the microphone equalizer dials (HI, LOW) to adjust the
tone of the microphone sound.
• The microphone equalizer function operates simultaneously
on microphone 1 and 2.
Use the BOOTH MONITOR LEVEL dial to adjust the sound
volume.
• The BOOTH MONITOR LEVEL dial can be used to adjust the
sound volume independently of the MASTER LEVEL dial.
Use the HEADPHONES CUE buttons (channels 1 to 4,
MASTER, EFFECTS) to select the source.
• The selected HEADPHONES CUE button lights brightly.
Set the headphones (MONO SPLIT/STEREO) switch.
• When HEADPHONES CUE ( 1 , 2 , 3 , 4 or EFFECTS ) button is
selected, the selected audio is output to the L channel.
When HEADPHONES CUE ( MASTER ) button is selected, the
master audio is output from the R channel.
• When set to the [ STEREO ] position, the sound
corresponding to the selected HEADPHONES CUE button is
output in stereo.
When [MONO SPLIT] is selected, use the MIXING dial to
adjust the balance of sound between the left channel (sound
selected with the HEADPHONES CUE button), and the right
channel (the master sound – but only when the
HEADPHONES CUE button for the [MASTER] is ON).
• When the MIXING dial is rotated clockwise (toward
[ MASTER ]), the master output (only when the
HEADPHONES CUE button for the [ MASTER ] is ON)
increases; when rotated counterclockwise (toward [ CUE ]),
the sound selected with the HEADPHONES CUE button is
output.
Use the LEVEL dial to adjust the headphones' sound volume.
13
En