Installation Standards; Safety Measures - Bio Bronpi ELSA Instructions D'installation, D'utilisation Et D'entretien

The restoration of the 80ºC safety device is not included in the warranty unless the technical assistance centre can demonstrate a faulty
component.
•
D6
Your stove has a flow pressure gauge (see drawing D6) connected to a sensor placed inside the primary air
suction pipe that detects the proper circulation of the combustion air and the smoke discharge. In case of
insufficient air inlet (due to incorrect smoke outlet or improper air intake), the sensor sends a "block" signal to the
stove.
The OASYS Plus TECHNOLOGY (Optimum Air System) allows a constant combustion by controlling automatically
the draft according to the characteristics of the flue (curves, length, diameter, etc) and the environmental
conditions (wind, humidity, atmospheric pressure, etc).
• CAPACITY SENSOR
The Paula model has a capacity sensor to detect the presence of fuel in the tank (hopper). The Elsa model lack this sensor. If the fuel falls
below a certain level for a certain period of time, the message "Er18" (No fuel) and the message NORMAL will alternate on the display, the
stove will operate normally after that time, the stove will enter into the alarm status "Er 18" and automatically will get on "final cleaning". In
order to deactivate the alarm, you must press the key
In order to start a new ignition, it is necessary to fill the fuel tank before pressing the on button of the stove, otherwise your stove will not show
any alarm but will not allow the ignition.
5

INSTALLATION STANDARDS

The way of installing the stove will affect the safety and the proper operation. For this reason, it is recommendable that the installation is
carried out by people who are qualified and informed about the compliance with the installation and safety norms.
If your equipment is not properly installed, it may cause serious damage.
Before the installation, follow the next verifications:
• Make sure that the floor can sustain the weight of the equipment and make a proper isolation in the case that it is made of flammable
material (wood) or a material that can be affected by a thermal shock (plaster cast, for example).
• If the equipment is installed on a floor which is not completely refractory or inflammable such as parquet, carpet, etc, it is necessary to
replace this part or introduce a fire-resistant base so that it protrudes out the oven 30 cm. Example of materials include steel flooring,
glass base or any other type of fire-resistant material.
• Make sure that there is proper ventilation in the place where it is installed (air intake).
• Avoid the installation in places where there are collective ventilation pipes, hoods with or without extractor, B type gas equipments,
heat pumps or equipments that can cause that the draw is not good if they are used at the same time.
• Make sure that the smoke duct and the pipes used for the chimney are suitable for the operation of the stove.
• Make sure that all the equipments have their own smoke duct. Do not use the same duct for various equipments.
• We recommend that you call your fitter in order to check both the chimney as well as the air flow for the combustion.
5.1

SAFETY MEASURES

During the installation of the equipment, there are risks to be taken into account, so you should follow the next safety measures:
a. Keep any flammable or heat sensitive materials (furniture, curtains, and clothing) at a minimum distance of about 150cm.
b. If the equipment is installed on a floor which is not completely refractory or inflammable it is necessary to replace this part or introduce
a fire-resistant base.
c. Do not place the stove near combustible walls or likely to be affected by a thermal shock.
d. The stove should only be used when the ash pan is inserted and the door closed.
e. It is recommended to install carbon monoxide detector (CO) in the room where the equipment is installed.
f. If you need a longer wire than the provided use it always with an earthed plug.
g. Do not install the stove in a bedroom.
h. The appliance should never be turned on in the presence of emission of gases or vapours (e.g., linoleum glue, gasoline, etc). Do not
place nearby flammable materials.
i. Solid combustion residues (ashes) should be collected in an airtight container and resistant to fire.
It is necessary to keep a safe distance when they are installed in
spaces where materials are susceptible of being flammables, either the
constructions materials or different materials that surround the stove (see
drawing D7).
References Flammable items
A
B
C
WARNING!! It is noted that both the stove and the glass get
very hot and should not be touched.
In case of fire in the stove or smoke duct:
a. Close the loading door.
b. Put the fire out by using carbon dioxide extinguishers (CO2
powder).
c. Request for the immediate intervention of the fire-fighters.
INSTALLATION, OPERATING AND SERVICING INSTRUCTIONS
FLOW SENSOR (Oasys Plus Technology)
for at least 3 seconds, and the stove will stop.
Non-flammable
items
1500 800
1500 150
1500 400
C
31
A
2
80-120 cm
CUBRE SUELO
ELSA AND PAULA
B
D7