Securing The Seat And Child In Using The Three-Point Seatbelt; Cleaning And Maintenance Of The Child Seat; Removing The Seat Cover; Replacing The Harness (See Also Chapter 3.1) 12 Id - RECARO YOUNG SPORT Instructions D'installation Et D'utilisation

3.2 Securing the seat and child in using the three-point seatbelt

∙ The recline position must not be used for group II or above!
∙ Allow your child to sit in the seat and insert the lap belt of the three-point seatbelt into the
front belt guides. Fasten the seatbelt buckle so that it closes with an audible click (fig. 24).
∙ Insert the diagonal belt into the guide on the headrest (fig. 25).
∙ Adjust the headrest for your child's height. The belt is in an optimal position when it runs
over the middle of the collarbone and not too close to the child's neck (fig. 26).
4.

Cleaning and maintenance of the child seat

The buckle must always lock into place with an audible click. If it does not, this may be
caused by dirt in the buckle. As a counter measure, the buckle can be removed (chapter
3.1) and cleaned with warm water. Before reinstalling, allow the buckle to dry thoroughly.
The buckle must not be lubricated with oil or grease. The cover of the RECARO Young Sport,
Young Sport HERO can be washed in the washing machine. Please remove all removable
foam pads from and out of the covers before washing. These pads must not be washed. We
recommend washing the cover at 30 °C on a gentle wash setting in order to protect the en-
vironment. If washed at higher temperatures the colors may fade. Do not spin and never dry
in a tumble drier, as the material and wadding could separate from one another.

4.1 Removing the seat cover

First release the cover from the buttons on the head, back and seat sections. You can then
simply remove the cover (fig. 27). Removing the seat cover is only possible if the harness
system has previously been removed (see chapter 3.1).
4.2 Replacing the harness (see also chapter 3.1)
Installation is made easier if the buckle tongues are locked in place in the buckle (fig. 11).
∙
∙ First unclip the base plate and turn it away to the side. Then remove the seat cushion and
place it to one side.
∙ Now insert the lap belt of the integral harness system from the top through the outer long
slit and downwards, then thread it through the inner slits back towards the top (1). Now
insert the locking plate into the loops (2) (fig. 28,29).
Important: All 4 lugs must be visible.
∙ Replace the seat cushion on the seat and insert the crotch strap through the opening from
above. Secure the loops with the mounting plate (fig. 30).
Important: All 4 hooks must lie outside the loops.
∙ Turn the base plate back to its original position and clip it in. Ensure that the T-section of the
adjuster strap remains readily accessible.
∙ Attach the cover to the seat and backrest.
Place the headrest in the 2nd position from the bottom and insert the retaining belt for the
∙
shoulder pads through the slits from front to back. Insert the guide rail as shown and pass
the retaining belt over the guide rail (fig. 31,32,33).
∙ Move the headrest up into the 3rd position and secure with the screw (fig. 34).
Now push the shoulder pads from back side through the slits in the headrest cover and
∙
place the cover on the headrest. Open the shoulder pads, insert the shoulder straps as
shown and insert these through the headrest from front to back. Ensure that you pass the
straps over the guide rail.
∙ Attach the shoulder straps to the T section. Important: Do not twist the straps (fig. 32,35).
Finally, close the shoulder pads and ensure, by pulling firmly on the straps, that all the
∙
connections are secure.
12