Lubrication - DeWalt DWE4884 Traduction De La Notice D'instructions Originale

ENglish
activation of a ground fault interrupter, throwing of a
circuit breaker, accidental unplugging, or power failure.
If the switch is locked on, the tool will start unexpectedly
when it is reconnected.

WARNING: Grasp tool firmly with both hands to maintain
control of the tool at start up and during use and until the
wheel or accessory stops rotating. Make sure the wheel
has come to a complete stop be fore laying the tool down.

WARNING: To reduce unexpected tool movement, do
not switch the tool on or off while under load conditions.
Allow the grinder to run up to full speed before touching
the work surface. Lift the tool from the surface before
turning the tool off.
Paddle Switch (Fig. A)
DWE4887N
The lock-off lever , located on the paddle switch, is a safety
4
feature that prevents accidental activation of the grinder.
To turn the tool on, push the lock-off lever
of the tool, then depress the paddle switch
while the switch is depressed. Turn the tool off by releasing the
paddle switch.

WARNING: Do not disable the lock-off lever. If the lock-off
lever is disabled, the tool may start unexpectedly when it
is laid down.
Slider Switch (Fig. A)
DWE4884
To start the tool, slide the ON/OFF slider switch
the front of the tool. To stop the tool, release the ON/OFF
slider switch.
For continuous operation, slide the switch toward the front of
the tool and press the forward part of the switch inward. To stop
the tool while operating in continuous mode, press the rear part
of the slider switch and release.

WARNING: Allow the tool to reach full speed before
touching tool to the work surface. Lift the tool from the
work surface before turning the tool off.
Metal Applications
When using the tool in metal applications, make sure that a
residual current device (RCD) has been inserted to avoid residual
risks caused by metal swarf.
If the power supply is shut off by the RCD, take the tool to
authorised D WALT repair agent.
e

WARNING: In extreme working conditions, conductive
dust can accumulate inside the machine housing when
working with metal. This can result in the protective
insulation in the machine becoming degraded with a
potential risk of an electrical shock.
To avoid build-up of metal swarf inside the machine, we
recommend to clear the ventilation slots on a daily basis.
See Maintenance.
8
MAINTENANCE
Your D
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.

Motor Brushes
Keep brushes clean and sliding freely in their guides. Carbon
brushes have varying symbols stamped into them, and if the
brush is worn down to the line closest to the spring, they must
be replaced. New brush assemblies are available at your local
service center.
4 toward the back
. The tool will run
1

Lubrication

Your power tool requires no additional lubrication.
Cleaning

1 toward

Optional Accessories

Consult your dealer for further information on the
appropriate accessories.
Protecting the Environment
be recovered or recycled reducing the demand for raw
materials. Please recycle electrical products and batteries
according to local provisions. Further information is available at
www.2helpU.com.
WALT power tool has been designed to operate
e
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. Be sure the
trigger switch is in the OFF position. An accidental start-up
can cause injury.
WARNING: Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing this procedure.
WARNING: Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into a liquid.
WARNING: Since accessories, other than those offered
by D WALT, have not been tested with this product, use
e
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only D
accessories should be used with this product.
Separate collection. Products and batteries marked
with this symbol must not be disposed of with normal
household waste.
Products and batteries contain materials that can
WALT recommended
e