Service Parts List - Milwaukee M18 Manuel De L'utilisateur

EXAMPLE:
00
0 Component Parts (Small #)
Are Included When Ordering
The Assembly (Large #).
37
38 (4x) 46
Place Rubber Cushions (37)
into slots of Housing Halves
(38 and 46) as shown.
52
Sharp side of retaining
54
ring (6) to face up
6
towards sleeve.
5
4
3
2
1
Side slots on gear case
cover (54) lock onto raised
bosses of gear case assembly (55).
FIG. PART NO. DESCRIPTION OF PART
1 34-60-0725 'C' Retaining Ring
2 45-88-1881 Washer
3 40-50-1470 Spring
4 45-22-2643 Sleeve
5 40-50-0012 Anvil Spring
6 34-60-0002 Retaining Ring
26 --------------- Planetary Gear
37 45-30-0022 Rubber Cushion
38 --------------- Right Housing Halve (Cover)
39 12-20-0076 Service Nameplate
40 06-82-7236 M3 x 16mm Pan Hd. ST T-10 TP Screw (8)
41 06-82-0013 M3 x 38mm Pan Hd. ST T-10 TP Screw (2)
44 06-82-0130 6-32 x 5/16" Pan Hd. T-15 Machine Scr (2)
46 --------------- Left Housing Halve (Support)
51 45-24-0013 Forward/Reverse Shuttle
52 42-55-2753 Blow Molded Carrying Case
53 02-02-0170 3.5mm Steel Ball
54 42-92-0054 Gear Case Cover

55 14-30-1027 Gearcase Assy. with Sleeve & Bearing (1)

56 14-46-0218 Pulse Unit (Sealed System)

57 14-30-1028 Gearcase End Cap Assembly w/ Gears (1)

58 44-66-0135 Gearcase End Cap Assembly

58a --------------- Ring Gear

58b --------------- End Cap with Bearing
59 31-44-0049 Housing Kit
60 43-72-0046 Bit Holder Kit

61 16-07-2985 Rotor Assembly

SERVICE PARTS LIST

SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS
M18™ FUEL™ SURGE™ 1/4" HEX HYDRAULIC DRIVER
2760-20
CATALOG NO.
39
40(8x)
38
44(2x)
60
44
41(2x)
56
53
55
54
5
56
NO. REQ.
STARTING
SERIAL
58b
58a
26
56
58a
58
58b
26
57
58
26 64
NOTE:
Place Anvil Spring (5) onto
anvil of Pulse Unit (56) with
curled end inserted into slot
of anvil as shown. Place Steel
53
Ball (53) in anvil slot in front
of spring.
FIG. PART NO.
62 14-20-0044
(1)
(1)
(1)
(1)
(1)
63 42-70-0059
(1)
64 45-24-0017
(3)
(4)
FIG. LUBRICATION
(1)
Use Type 'J' Grease, No. 49-08-4220 (1 lb. can)
(1)
57,61 When servicing Pinion of the Rotor Assembly (61), the inside
cavity and gearing system of Gearcase End Cap Assy. (57):
90-95% of the old grease must be removed prior to any
new grease being added.
(1)
(1)
4 Place a very light coating of grease on the ID of the sleeve.
(1)
55 Coat inside sleeve and bearing on front gearcase with grease.
(1)
56 Place a dab of grease in the ball slot of anvil on pulse unit.
(1)
26,56 On the rear of the pulse unit, heavily coat the three gears and
the pins they ride on with grease.
(1)
58a Place a heavy coat of grease to teeth on inside cavity of the
ring gear.
(1)
61 Coat pinion of rotor assembly with grease.
(1)
(1)
(1)
(1)
(1)
REVISED BULLETIN
54-26-2800
WIRING INSTRUCTION
H16B
SEE PAGE 2
NOTE:
Assemble the three planet gears (26) on the posts of the
pulse unit (56). Place the ring gear (58a) and end cap
with bearing (58b) onto the pulse unit. Turn the anvil on
the pulse unit to rotate the gears to seat the end cap
properly. Align the tab on the end cap with the notch in the
gear case to install.
61
62
51
DESCRIPTION OF PART
Electronics Assembly
Consisting of: On-Off Switch, Main
PCBA, Stator, LED, HV Protection,
Selector PCBA and Battery Connector
Block
Belt Clip Kit
Speed Selector Assembly
MILWAUKEE TOOL l www.milwaukeetool.com
13135 W. Lisbon Road, Brookfield, Wisc. 53005
BULLETIN NO.
54-26-2801
DATE
Sept. 2020
= Part number change
from previous service
parts list.
37 38
59
39 46
46 44
63
44
NO. REQ.
(1)
(1)
(1)
Drwg. 1