Télécharger Imprimer la page

Publicité

Liens rapides

IMPORTANT SAFETY INSTRUCTIONS
WARNING
READ AND UNDERSTAND ALL INSTRUCTIONS.
listed below, may result in electric shock, fire and/or serious personal injury.
SAVE THESE INSTRUCTIONS.
1. SAVE THESE INSTRUCTIONS - THIS OPERATOR'S MANUAL CONTAINS IMPORTANT SAFETY AND
OPERATING INSTRUCTIONS FOR MILWAUKEE LI-ION BATTERY PACKS AND THE MILWAUKEE
LI-ION CHARGER.
2. BEFORE USING THE BATTERY PACK AND CHARGER, READ THIS OPERATOR'S MANUAL, YOUR
TOOL OPERATOR'S MANUAL, AND ALL LABELS ON THE BATTERY PACK, CHARGER AND TOOL.
3. CAUTION - TO REDUCE THE RISK OF INJURY, CHARGE MILWAUKEE LITHIUM-ION PACKS ONLY IN THEIR
MILWAUKEE LITHIUM-ION CHARGER. Other types of chargers may cause personal injury or damage. Do not wire
a battery pack to a power supply plug or car cigarette lighter. Battery packs will be permanently disabled or damaged.
4. AVOID DANGEROUS ENVIRONMENTS. Do not charge battery pack in rain, snow, damp or wet locations. Do
not use battery pack or charger in the presence of explosive atmospheres (gaseous fumes, dust or flammable
materials) because sparks may be generated when inserting or removing battery pack, possibly causing fire.
5. CHARGE IN A WELL VENTILATED AREA. Do not block charger vents. Keep them clear to allow proper
ventilation. Do not allow smoking or open flames near a charging battery pack. Vented gases may explode.
6. DO NOT BURN OR INCINERATE BATTERY PACKS. Battery packs may explode, causing personal injury
or damage. Toxic fumes and materials are created when battery packs are burned.
7. DO NOT CRUSH, DROP, OR DAMAGE battery pack. Do not use a battery pack or charger that has received
a sharp blow, been dropped, run over, or damaged in any way (e.g., pierced with a nail, hit with a hammer,
stepped on).
8. DO NOT DISASSEMBLE. Incorrect reassembly may result in the risk of electric shock, fire or exposure to
battery chemicals. If it is damaged, take it to a MILWAUKEE service facility.
9. BATTERY CHEMICALS CAUSE SERIOUS BURNS. Never allow contact with skin, eyes, or mouth. If a
damaged battery pack leaks battery chemicals, use rubber or neoprene gloves to dispose of it. If skin is
exposed to battery fluids, wash with soap and water and rinse with vinegar. If eyes are exposed to battery
chemicals, immediately flush with water for 20 minutes and seek medical attention. Remove and dispose of
contaminated clothing.
10. DO NOT SHORT CIRCUIT. A battery pack will short circuit if a metal object makes a connection between
the positive and negative contacts on the battery pack. Do not place a battery pack near anything that may
cause a short circuit, such as coins, keys or nails in your pocket. Do not allow fluids to flow into battery pack.
Corrosive or conductive fluids, such as seawater, certain industrial chemicals, and bleach or bleach contain-
ing products, etc., can cause a short circuit. A short circuited battery pack may cause fire, personal injury,
and product damage.
11. STORE YOUR BATTERY PACK AND CHARGER in a cool, dry place. Do not store battery pack where tem-
peratures may exceed 120°F (50°C) such as in direct sunlight, a vehicle or metal building during the summer.
READ AND SAVE ALL INSTRUCTIONS FOR FUTURE REFERENCE.
SYMBOLOGY
Volts
Direct Current
Do not allow battery to contact
corrosive or conductive fluid
Properly Recycle Batteries
Charging Temperature
Recommended Ambient Charging Temperature ................................................................... 40°F to 105°F
Fuel Gauge
Use the Fuel Gauge to determine the battery pack's remaining run
time. Press the Fuel Gauge button to display the lights. The
Fuel Gauge will light up for 2-3 seconds. When less than 10%
of charge is left, 1 light on the fuel gauge will flash slowly.
NOTE: If the Fuel Gauge doesn't appear to be working, place
the battery pack on the charger and charge as needed.
Compared to NiCd battery pack types, MILWAUKEE Lithium-Ion
battery packs deliver fade-free power for their entire run time.
To signal to you that the battery pack is at the end of its run
time and needs to be charged, power to the tool will drop
quickly. When this happens, remove the tool from the workpiece
and charge the battery pack as needed. If the tool begins to "pulse",
but not run, charge the battery pack immediately.
NOTE: Immediately after using the battery pack, the Fuel
Gauge may display a lower charge than it will if checked a few
minutes later. The battery cells "recover" some of their charge
after resting.
Battery Pack Protection
To protect itself from damage and extend its life, the battery
pack's intelligent circuit monitors current draw and temperature.
In extremely high torque, binding, stalling, and short circuit situ-
ations, the battery pack will turn OFF the tool if the current draw
becomes too high. In these situations, the tool may "buzz" for
about 2 seconds before it turns OFF. To prevent the tool from
turning OFF, immediately reduce pressure on the application
or release the trigger.
If the tool does turn off, the Fuel Gauge lights will flash 11 times. Release the trigger to reset. Under ex-
treme circumstances, the internal temperature of the battery could become too high. If this happens,the
battery pack will shut off. When the Fuel Gauge button is pressed, the lights will flash alternatingly. Allow
the battery pack to cool. The battery is ready for use when the Fuel Gauge displays the remaining run time
when the Fuel Gauge button is pressed.
Cold Weather Operation
MILWAUKEE Lithium-Ion battery packs are designed to operate in temperatures below freezing. When
the battery pack is too cold, it may need to warm up before normal use. Put the battery on a tool and use
the tool in a light application. It may "buzz" for a short time until it warms up. When the buzzing stops, use
the tool normally.
TO REDUCE THE RISK OF FIRE, PERSONAL INJURY, AND PRODUCT DAMAGE
WARNING
DUE TO A SHORT CIRCUIT, NEVER IMMERSE YOUR TOOL, BATTERY PACK OR
CHARGER IN FLUID OR ALLOW A FLUID TO FLOW INSIDE THEM. CORROSIVE OR CONDUC-
TIVE FLUIDS, SUCH AS SEAWATER, CERTAIN INDUSTRIAL CHEMICALS, AND BLEACH OR
BLEACH CONTAINING PRODUCTS, ETC., CAN CAUSE A SHORT CIRCUIT.
Maintenance and Storage
Do not expose your battery pack or cordless tools to water or rain, or allow them to get wet. This could
damage the tool and battery pack. Do not use oil or solvents to clean or lubricate your battery pack. The
plastic casing will become brittle and crack, causing a risk of injury.
Store battery packs at room temperature away from moisture. Do not store in damp locations where cor-
rosion of terminals may occur. As with other battery pack types, permanent capacity loss can result if the
pack is stored for long periods of time at high temperatures (over 120° F). MILWAUKEE Lithium-Ion bat-
tery packs maintain their charge during storage longer than other battery pack types. After about a year of
storage, charge the pack as normal.
Disposing of MILWAUKEE Li-Ion Battery Packs
MILWAUKEE Lithium-Ion battery packs are more environmentally friendly than some other types of power
tool battery packs (e.g., nickel-cadmium). Always dispose of your battery pack according to federal, state
and local regulations. Contact a recycling agency in your area for recycling locations.
Even discharged battery packs contain some energy. Before disposing, use electrical tape to cover the
terminals to prevent the battery pack from shorting, which could cause a fire or explosion.
TO REDUCE THE RISK OF INJURY OR EXPLOSION, NEVER BURN OR INCINER-
WARNING
ATE A BATTERY PACK EVEN IF IT IS DAMAGED, DEAD OR COMPLETELY DIS-
CHARGED. WHEN BURNED, TOXIC FUMES AND MATERIALS ARE CREATED.
RBRC Battery Recycling Seals
The RBRC™ Battery Recycling Seals (see "Symbology") on your tool battery packs indicate that
MILWAUKEE has arranged for the recycling of that battery pack with the Rechargeable Battery Recycling
Corporation (RBRC). At the end of your battery pack's useful life, return the battery pack to a MILWAUKEE
Branch Office/Service Center or the participating retailer nearest you. For more information, visit the RBRC
web site at www.rbrc.org.
Limited Warranty
Every MILWAUKEE Battery Pack (sold with cordless product and/or as a replacement battery pack) is warranted to the original purchaser only to be free
from defects in material and workmanship. Subject to certain exceptions, MILWAUKEE will repair or replace a battery pack which, after examination, is
determined by MILWAUKEE to be defective in material or workmanship for the stated warranty period from date of purchase. Return of the battery pack to
a MILWAUKEE factory Service Center location or MILWAUKEE Authorized Service Station, freight prepaid and insured, is required. For the proper shipping
procedure of battery packs, contact 1.800.SAWDUST (1.800.729.3878), or go to www.milwaukeetool.com. A copy of the proof of purchase should be included
with the return product. This warranty does not apply to damage that MILWAUKEE determines to be from repairs made or attempted by anyone other than
MILWAUKEE authorized personnel, misuse, alterations, abuse, normal wear and tear, lack of maintenance, or accidents.
Battery Pack Cat. No.
48-11-1812, 48-11-1828 (Serial number prefix "B41E" and later), 48-11-1840,
48-11-1850, 48-11-1860, 48-11-1865, 48-11-1890, 48-11-2402, 48-11-2440,
48-11-2460, 48-11-2830 (Serial number prefix "C71")
48-11-0490, 48-11-1815, 48-11-1820, 48-11-2001, 48-11-2401, 48-11-2420,
48-11-2430
48-11-1828 (Serial number prefix "B41D" and earlier), 48-11-1830 (Serial
number prefix "A95"), 48-11-2830 (Serial number prefix "A71")
48-11-0100, 48-11-1024, 48-11-1830 (Serial number prefix "E95"),
48-11-1970, 48-11-2230
LITHIUM-ION BATTERY PACKS
BLOC DE PILES AU LITHIUM-ION
PAQUETE DE BATERÍA DE IONES DE LITIO
Failure to follow all instructions
FUNCTIONAL DESCRIPTION
Release button
Fuel gauge
Fuel gauge
button
Release button
Approximate Run
78-100%
Time Remaining
55-77%
33-54%
10-32%
Less than 10% if bottom light is flashing
Fuel Gauge Lights Diagnosis
Solution
Lights 1 - 4 Solid Remaining run
Continue
time
working
1 Light, flashing
Less than 10%
Prepare to
slowly
run time left
charge pack
1 Light, flashing
End of
Charge pack
quickly
discharge
Lights 1-4,
Current draw
Release trigger
flashing quickly
too high
and restart,
reduce pressure
Lights 1&3 /
Battery
Release trigger
2&4, flashing
temperature
and allow
alternatingly
too high
battery to cool
Warranty Period
Chemistry
(from date of purchase)
LITHIUM-ION
Three (3) Years
LITHIUM-ION
Two (2) Years
Two (2) Years – plus, Three
LITHIUM-ION
(3) Years Pro-Rata (prorated)*
Nickel-Cadmium (Ni-Cd), Nickel-Metal-
One (1) Year
Hydride (Ni-MH), LITHIUM-ION
*The warranty period for MILWAUKEE M18™ 48-11-1828 (with the serial number prefix "B41D" and earlier), V18™48-11-1830 (with the serial
number prefix "A95"), and V28™ 48-11-2830 (with the serial number prefix "A71") is five (5) years / 2000 charges from the date of purchase, which-
ever first occurs. The first 1000 charges or 2 years of the warranty, whichever first occurs, are covered through free replacement of the defective
battery. This means that for the earlier of the first 1000 charges or two (2) years from the date of purchase/first charge, a replacement battery will be
provided to the customer for any defective battery free of charge. Thereafter, the remaining charges up to a total of 2000 or the remainder of the five
(5) year period from the date of purchase, whichever first occurs, will be covered on a pro rata basis. This means that every customer gets an ad-
ditional 1000 charges or three (3) years of pro rata warranty on the these battery packs, depending upon the amount of use. MILWAUKEE M18™
48-11-1828 (with the serial number prefix "B41E" and later), V18™48-11-1830 (with the serial number prefix "E95"), and M28™ 48-11-2830 (with the serial
number prefix "C71") have different warranty periods, as listed.
Warranty Registration is not necessary to obtain the applicable warranty on a MILWAUKEE battery pack. The manufacturing date of the product will be used
to determine the warranty period if no proof of purchase is provided at the time warranty service is requested.
ACCEPTANCE OF THE EXCLUSIVE REPAIR AND REPLACEMENT REMEDIES DESCRIBED HEREIN IS A CONDITION OF THE CONTRACT FOR THE
PURCHASE OF EVERY MILWAUKEE PRODUCT. IF YOU DO NOT AGREE TO THIS CONDITION, YOU SHOULD NOT PURCHASE THE PRODUCT. IN
NO EVENT SHALL MILWAUKEE BE LIABLE FOR ANY INCIDENTAL, SPECIAL, CONSEQUENTIAL OR PUNITIVE DAMAGES, OR FOR ANY COSTS,
ATTORNEY FEES, EXPENSES, LOSSES OR DELAYS ALLEGED TO BE AS A CONSEQUENCE OF ANY DAMAGE TO, FAILURE OF, OR DEFECT IN ANY
PRODUCT INCLUDING, BUT NOT LIMITED TO, ANY CLAIMS FOR LOSS OF PROFITS. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITA-
TION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. THIS WARRANTY
IS EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS WARRANTIES, WRITTEN OR ORAL. TO THE EXTENT PERMITTED BY LAW, MILWAUKEE
DISCLAIMS ANY IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR USE OR PURPOSE; TO THE EXTENT SUCH DISCLAIMER IS NOT PERMITTED BY LAW, SUCH IMPLIED WARRANTIES ARE LIMITED
TO THE DURATION OF THE APPLICABLE EXPRESS WARRANTY AS DESCRIBED ABOVE. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW
LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU, THIS WARRANTY GIVES YOU SPECIFIC LEGAL
RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
This warranty applies to product sold in the U.S.A. and Canada only.
Please consult the 'Service Center Search' in the Parts & Service section of MILWAUKEE's website www.milwaukeetool.com
or call 1.800.SAWDUST (1.800.729.3878) to locate your nearest service facility for warranty and non-warranty service on a MILWAUKEE Battery Pack.
RÈGLES GÉNÉRALES DE SÉCURITÉ
LIRE ET COMPRENDRE TOUTES LES INSTRUCTIONS.
AVERTISSEMENT
respect des instructions ci-après peut entraîner des chocs électriques, des incen-
dies et/ou des blessures graves.
CONSERVER CES STRUCTIONS.
1. CONSERVER CES INSTRUCTIONS - CE MANUEL DE L'OPÉRATEUR CONTIENT DES INSTRUC-
TIONS IMPORTANTES EN MATIÈRE DE SÉCURITÉ ET DE FONCTIONNEMENT POUR LE BLOC
DE PILES AU LITHIUM-ION 18V MILWAUKEE.
2. AVANT D'UTILISER LE BLOC DE PILES ET LE CHARGEUR, LIRE CE MANUEL DE L'OPÉRATEUR,
LE MANUEL DE L'OPÉRATEUR DE L'OUTIL ET TOUTES LES ÉTIQUETTES DU BLOC DE PILES,
DU CHARGEUR ET DE L'OUTIL.
3. MISE EN GARDE! POUR MINIMISER LES RISQUES DE BLESSURES CORPORELLES, SEULE LE
BLOC DE PILES AU LI-ION MILWAUKEE DOIT ÊTRE RECHARGÉE AVEC CHARGEUR AU LI-ION.
D'autres types de chargeurs peuvent causer des blessures ou des dommages. Ne pas relier un bloc de piles
à une prise d'alimentation électrique ou à un allume-cigare de voiture pour ne pas désactiver ou endommager
de façon permanente le bloc de piles.
4. ÉVITEZ LES ENVIRONNEMENTS À RISQUES. N'UTILISEZ PAS LE CHARGEUR SOUS LA PLUIE,
la neige ou dans les endroits humides ou mouillés. Ne vous servez pas du chargeur ou du bloc de piles en
milieux explosifs (émanations de gaz, poussière ou substances inflammables), car il pourrait se produire des
étincelles, lors de l'insertion du bloc de piles dans le chargeur ou lors de son retrait, créant un risque d'incendie.
Contacts
5. RECHARGEZ DANS UN ENDROIT BIEN VENTILÉ. Ne laissez pas les évents du chargeur se bloquer et
assurez-vous qu'ils sont bien ventilés. N'effectuez pas une recharge du bloc de piles à proximité d'une flamme
vive ou fumante, afin d'éviter l'explosion des décharges de gaz.
6. NE PAS BRÛLER OU INCINÉRER LE BLOC DE PILES. Le bloc de piles peuvent exploser et causer
des blessures ou des dommages. Des gaz et des matériaux toxiques sont créés lorsque le bloc de piles au
lithium-ion sont brûlées.
7. NE PAS ÉCRASER, LAISSER TOMBER OU ENDOMMAGER le bloc de piles. Ne pas utiliser une bloc de
piles ou un chargeur qui ont reçu choc important, qui sont tombés, ont été écrasés ou endommagés de quelle
que façon que ce soit (par exemple percés par une pointe, heurtés par un marteau, piétinés).
8. NE PAS DÉMONTER. Un remontage incorrect peut causer des risques de chocs électriques, d'incendies
ou d'exposition des produits chimiques du bloc de piles. Si elle est endommagée, l'apporter à un centre
d'entretien MILWAUKEE.
9. LE LIQUIDE DU BLOC DE PILES PEUT CAUSER DES BRÛLURES CHIMIQUES GRAVES. Ne permettez
jamais que le liquide du bloc de piles ne vienne en contact avec la peau ou les yeux. Si du liquide s'écoule
d'une bloc de piles, mettez des gants de caoutchouc ou de néoprène pour disposer du liquide. Si la peau
vient en contact avec le liquide, lavez-la à l'eau savonneuse et rincez-la ensuite au vinaigre. Enlevez les
vêtements souillés et disposez-en. Si les yeux sont affectés, arrosez-les immédiatement avec de l'eau en
abondance pendant 20 minutes et demandez l'aide d'un médecin.
10. ATTENTION AUX COURTS-CIRCUITS! Un bloc-piles court-circuite si un objet métallique établit une con-
nexion entre les contacts positifs et négatifs sur le bloc-piles. Ne placez pas un bloc-piles près de tout ce
qui peut causer un court-circuit, comme des pièces de monnaie, des clés ou des clous dans votre poche.
Ne pas laisser les fluides s'écouler dans le bloc-piles. Les fluides corrosifs ou conducteurs, tels que l'eau de
mer, certains produits chimiques industriels, les produits de blanchiment ou de blanchiment, etc., peuvent
provoquer un court-circuit. Un bloc-batterie court-circuité peut provoquer des incendies, des blessures cor-
porelles et des dommages au produit.
11. RANGEZ LE BLOC DE PILES ET LE CHARGEUR dans un endroit sec et frais. Ne rangez pas le bloc de
piles dans un endroit où la température pourrait dépasser 50°C (120°F), comme par exemple un véhicule
ou une structure métallique en été.
LIRE ET CONSERVER TOUTES LES INSTRUCTIONS POUR
PICTOGRAPHIE
Volts
Courant direct
Ne pas permettre que le bloc-piles
soit en contact les fluides corrosifs
ou conducteurs
Recyclage correct des batteries
Température de chargement
Température ambiante de charge recommandée .............................................5°C à 40°C (40°F à 105°F)
Indicateur de charge de la pile
Utiliser l'indicateur de charge de la pile pour déterminer l'autonomie
restante du bloc de piles. Appuyer sur le bouton de l'indicateur
de charge de la pile pour afficher les témoins. L'indicateur de
charge de la pile s'allume pendant 2 à 3 secondes. Un témoin
sur l'indicateur de charge de la pile clignotera lentement s'il
reste moins de 10 % de la charge.
NOTE : Si l'indicateur de charge de la pile ne semble pas
fonctionner, placer le bloc de piles sur le chargeur et le charger,
au besoin.
Contrairement aux blocs de piles au nickel-cadmium, les
blocs-piles au lithium-ion MILWAUKEE offrent une puissance
constante tout au long de leur durée d'utilisation. Pour signaler
à l'utilisateur que la batterie est à la fin de sa durée de fonc-
tionnement et nécessite d'être chargée, l'alimentation de l'outil
chute rapidement. Si l'outil commence à «pulser» sans se mettre
en marche, charger immédiatement la batterie.
NOTE : Immédiatement après utilisation du bloc de piles,
l'indicateur de charge de la pile peut afficher une charge
inférieure qu'il ne le ferait quelques minutes plus tard. Les
éléments de la pile « récupèrent » une partie de leur charge
après une période de repos.
Protection du bloc de piles
Pour protéger le bloc de piles et prolonger sa durée de vie,
le circuit intelligent du bloc de piles surveille les appels de
courant et la température. En cas de couple extrêmement
élevé, de coincement, de calage et de courts-circuits, le bloc
de piles mettra l'outil HORS TENSION si l'appel de courant
est trop élevé. Dans la plupart des cas, l'outil vibre pendant 2
secondes environ avant que la batterie se ferme. Pour éviter
qu'elle se ferme automatiquement, réduire immédiatement la
pression sur l'application ou relâcher le déclencheur.
Si l'outil s'éteint, les lumières de mesure de carburant clignoteront 11 fois. Relâcher la gâchette et redé-
marrer l'outil. Dans des conditions extrêmes, la température interne de la pile peut devenir excessive. Si
cela se produit, les témoins de l'indicateur de charge de la pile clignoteront en alternance et l'outil cessera
de fonctionner. Laisser la pile refroidir. La pile est prête à l'emploi lorsque la jauge de carburant affiche la
durée de fonctionnement restante lorsque le bouton de jauge de carburant est pressé.
Fonctionnement par temps froid
Le bloc de batteries au lithium-ion de MILWAUKEE sont conçus pour fonctionner à des températures infé-
rieures au point de congélation. Lorsque le bloc des batteries est très froid, mettre le bloc des batteries sur
l'outil et utiliser celui-ci pour une utilisation légère. Une alarme sonore peut se faire entendre pendant un
court instant jusqu'à ce qu'il se réchauffe. Lorsque l'alarme s'arrête, utiliser l'outil normalement.
POUR RÉDUIRE LE RISQUE D'INCENDIE, DE BLESSURES CORPORELLES
AVERTISSEMENT
ET DE DOMMAGES CAUSÉS PAR UN COURT-CIRCUIT, NE JAMAIS IM-
MERGER L'OUTIL, LE BLOC-PILES OU LE CHARGEUR DANS UN LIQUIDE OU LAISSER
COULER UN FLUIDE À L'INTÉRIEUR DE CELUI-CI. LES FLUIDES CORROSIFS OU CONDUC-
TEURS, TELS QUE L'EAU DE MER, CERTAINS PRODUITS CHIMIQUES INDUSTRIELS, LES
PRODUITS DE BLANCHIMENT OU DE BLANCHIMENT, ETC., PEUVENT PROVOQUER UN
COURT-CIRCUIT.
New batteries must be charged before first use.
Les batteries neuves doivent être chargées avant leur
utilisation initiale.
Las baterías nuevas se deben cargar antes de usarlas
por primera vez.
RÉFÉRENCE FUTURE.
DESCRIPTION FONCTIONNELLE
Boutons de libération
Indicateur
de niveau
d'énergie
Languette
de l'indicateur
de niveau
d'énergie
Durée approximative
de fonctionnement
restante
33-54%
10-32%
Moins de 10% - 1 témoin clignotant
Témoins de
l'indicateur
de charge de
la pile
Diagnostic
Témoins
Autonomie
1 à 4 – allumés
restante
1 témoin –
Moins de 10%
clignote
d'autonomie
lentement
restante
1 témoin –
Fin de la
clignote
décharge
rapidement
Témoins
Appel de
1 à 4 –
courant trop
clignotent
élevé
rapidement
Témoins 1 et
Température
3 ou 2 et 4 –
de la pile trop
clignotent en
élevée
alternance
Le non-
Contacts
Boutons de
libération
78-100%
55-77%
Solution
Poursuivre le travail
Se préparer à
charger le bloc de
piles
Charger le bloc de
piles
Relâcher la
gâchette et
redémarrer, réduire
la pression
Relâcher la
gâchette et laisser
la pile refroidir

Publicité

loading

Sommaire des Matières pour Milwaukee M18

  • Page 1 SAVE THESE INSTRUCTIONS. ditional 1000 charges or three (3) years of pro rata warranty on the these battery packs, depending upon the amount of use. MILWAUKEE M18™ 48-11-1828 (with the serial number prefix "B41E" and later), V18™48-11-1830 (with the serial number prefix “E95”), and M28™ 48-11-2830 (with the serial number prefix "C71") have different warranty periods, as listed.
  • Page 2 ésta en una tarea ligera. Es posible que “zumbe” por un breve período de tiempo hasta que se caliente. de série « A95 ») et 48-11-2830 V28™ (avec préfix de numéro de série « A71 ») de MILWAUKEE est de cinq (5) ans / 2 000 charges à compter de la date Una vez que el zumbido cese, utilice la herramienta de manera normal.