Panasonic WV-CS570/G Mode D'emploi page 13

DIP Switch 1
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
* When using the Unit Number 1 to 96 setting, the unit number setting needs to be configured using the RS485 SET
UP menu. For details about configuring this setting, see step 2 and page 19.
* Turning on power when this setting is selected causes the RS485 SET UP menu to appear during the initialization
routine.
I RS485 Communication Parameters (DIP Switch 1)
Configuring DIP Switch 1 as shown below resets communication parameters to their factory default settings. You can
then change the settings as desired.
DIP Switch 1
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON ON
1 2 3 4 5 6 7 8
Perform the following steps to use this setting.
(1) Turn off the camera and use DIP Switch 1 to configure RS485 communication parameters as shown above.
(2) Turn on the camera.
This applies the setting you configured in step (1).
(3) Turn off the camera, use DIP Switch 1 to set the unit number (pages 12 and 13), and then turn the camera back on
again.
Unit
DIP Switch 1
Number
ON
69
1 2
ON
70
1 2
ON
71
1 2
ON
72
1 2
ON
73
1 2
ON
74
1 2
ON
75
1 2
ON
76
1 2
ON
77
1 2
This setting resets communication parameters to the factory default settings.
BAUD RATE : 19 200 bit/s, DATA BIT : 8 bit, PARITY CHECK : NONE, STOP BIT : 1 bit
BAUD RATE : 9 600 bit/s, DATA BIT : 8 bit, PARITY CHECK : NONE, STOP BIT : 1 bit
BAUD RATE : 4 800 bit/s, DATA BIT : 8 bit, PARITY CHECK : NONE, STOP BIT : 1 bit
Unit
Number
78
3 4 5 6 7 8
79
3 4 5 6 7 8
80
3 4 5 6 7 8
81
3 4 5 6 7 8
82
3 4 5 6 7 8
83
3 4 5 6 7 8
84
3 4 5 6 7 8
85
3 4 5 6 7 8
86
3 4 5 6 7 8
Setting Description
-13-
DIP Switch 1
Number
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
Unit
87
88
89
90
91
92
93
94
95