Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Timer setup (BB2 optional)
Operating Instructions for built-in
electronic timers
1 Channel set-up
Safety instructions
Please note:
Main connection 115 or 220-240
V / 50-60 Hz !
Always turn power off and ensure
there is no voltage !
115 or 220-240V is life
threatening !
Installation should only be undertaken
by a competent electrician or other
qualified person!
Control and display elements
Symbol "light bulb"
2
3
1
4
5
6
9
7
Fig 1: Operating and Display Elements 1
Channel set-up
Display with Time and Switch
Points.
Sliding switches to set operating
mode:
AUTO: Switches on and off in
accordance with programmed switch
times
I: Permanently ON
O: Permanently OFF
Sliding switches to set Time and
Switch Times:
RUN : Switch program and clock run
: Set current time
: Input switch times
P
General information for buttons
(), 1..7 (), h () and m ():
Short pressing of these buttons gives:
counting up by 1 digit.
Pressing for longer than 3 seconds
effects: more rapid and continuous
counting up.
: Button for programming the 16
P
switch points;
When time switch points 1, 3, 5,
7, 9, 11, 13, 15 (activate time
points) are selected, the symbol
will appear in the right of the
display.
If time switch points 2, 4, 6, 8,
10, 12, 14, 16 (switch off time
points) are selected, there will
be no symbol.
1..7: Button to input the day of the
week (current day and daily
switch). When programming
timing points and individual
days the following block day
programmer are also possible:
1..5 (Monday to Friday)
1..6 (Monday to Saturday)
6..7 (Saturday to Sunday)
1..7 (Monday to Sunday)
h : Button to input hours (for
current time and switching
time).
m : Button to input minutes (for
current time and switching
time).
-X->: Skip function:
Pressing the Skip-button '-X->'
results in the fitted timer
reverting to the opposite
function mode.
For example: If the timer is in
„switched on" mode, it will be
immediately switched off and
vice-versa.
8
R : Reset button will delete all
switching times and current
time of day.
Reset
Before the first commissioning /
programming a Reset must be carried
out:
1. Ensure that sliding switch is in
the RUN position.
2. Press button R () with the point of
a biro or similar implement.
The Display will start to flash 0:00.
Setting the time and day
1. For 1 channel set-up:
Set the sliding switch to position
P
_
2. Press button 1...7 () to input the
day of the week (1 = Monday, 7 =
- 42 -
Sunday). An arrow will be seen in
the Display indicating the day of
the week.
3. Use buttons h () and m () to set
the time.
4. For 1 Channel set-up: Set sliding
switch to the RUN position. The
time of day will be activated.
The time of day will be activated
immediately.
Permanently ON, permanently OFF,
AUTO
To set these functions ensure that
sliding switch is in the RUN position.
1 Channel
Set sliding
Permanently ON
switch to
position I.
The appliance(s)
connected is(are)
The symbol
permanently
shows in
switched on
Display.
Set sliding
Permanently OFF
switch to
The appliance(s)
position 0.
connected is(are)
The symbol is
permanently
switched off
extinguished.
Set sliding
switch to
position AUTO.
AUTO
ON Mode:
The appliance(s)
symbol
connected switch
appears.
according to a pre-
set programmer
OFF Mode:
symbol is
extinguished.
Programming Switching Times
Each Channel has 16 programmable
Switching Points (8 x ON, 8 x OFF):
Nos. 1, 3, 5, 7, 9, 11, 13, 15 are Switch
ON points (symbol ).
Nos. 2, 4, 6, 8, 10, 12, 14, 16 are
Switch OFF points (no symbol).
The Switch Time selected will be
indicated by a number in the lower
right of the Display and the symbol .
1 Channel set-up
ON
OFF
Publicité
Table des Matières
